參數資料
型號: L5980TR
廠商: STMICROELECTRONICS
元件分類: 穩壓器
英文描述: 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
封裝: 3 X 3 MM, 1.08 MM HEIGHT, ROHS COMPLIANT, VFQFPN-8
文件頁數: 5/42頁
文件大小: 1188K
代理商: L5980TR
L5980
Functional description
Doc ID 13003 Rev 6
13/42
4.4
Overcurrent protection
The L5980 implements the overcurrent protection sensing current flowing through the power
MOSFET. Due to the noise created by the switching activity of the power MOSFET, the
current sensing is disabled during the initial phase of the conduction time. This avoids an
erroneous detection of a fault condition. This interval is generally known as “masking time”
or “blanking time”. The masking time is about 200 ns.
When the overcurrent is detected, two different behaviors are possible depending on the
operating condition.
1.
Output voltage in regulation. When the overcurrent is sensed, the power MOSFET is
switched off and the internal reference (VREF), that biases the non-inverting input of the
error amplifier, is set to zero and kept in this condition for a soft-start time (TSS, 2048
clock cycles). After this time, a new soft-start phase takes place and the internal
reference begins ramping (see Figure 8.a).
2.
Soft-start phase. If the overcurrent limit is reached the power MOSFET is turned off
implementing the pulse by pulse overcurrent protection. During the soft-start phase,
under overcurrent condition, the device can skip pulses in order to keep the output
current constant and equal to the current limit. If at the end of the “masking time” the
current is higher than the overcurrent threshold, the power MOSFET is turned off and it
will skip one pulse. If, at the next switching on at the end of the “masking time” the
current is still higher than the threshold, the device will skip two pulses. This
mechanism is repeated and the device can skip up to seven pulses. While, if at the end
of the “masking time” the current is lower than the overcurrent threshold, the number of
skipped cycles is decreased of one unit. At the end of soft-start phase the output
voltage is in regulation and if the overcurrent persists the behavior explained above
takes place. (see Figure 8.b)
So the overcurrent protection can be summarized as an “hiccup” intervention when the
output is in regulation and a constant current during the soft-start phase. If the output is
shorted to ground when the output voltage is on regulation, the overcurrent is triggered and
the device starts cycling with a period of 2048 clock cycles between “hiccup” (power
MOSFET off and no current to the load) and “constant current” with very short on-time and
with reduced switching frequency (up to one eighth of normal switching frequency). See
Figure 30 for short circuit behavior.
相關PDF資料
PDF描述
L5983 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
L5983TR 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
L5986A 3.9 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
L5986ATR 3.9 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
L5986TR 3.9 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
L5980TR-CUT TAPE 制造商:ST 功能描述:L5980 Series 15 V 250 kHz 0.7 A Step Down Switching Regulator - VFQFPN-8
L5981 功能描述:直流/直流開關調節器 1A STEP-DOWN SWITCH REG RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
L5981_08 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 A step-down switching regulator
L5981TR 功能描述:直流/直流開關調節器 1a Step-Down Switching Reg RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
L5983 功能描述:直流/直流開關調節器 1.5A STEP-DOWN SWITCHING REGULATOR RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5