- 您現在的位置：買賣IC網 > PDF目錄43899 > L4990D (STMICROELECTRONICS) 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | L4990D |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | SO-16 |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 322K |
| 代理商： | L4990D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
Layout hints. Generally speaking a proper cir-
cuitboard layout is vital for correct operation but is
not an easy task. Careful component placing, cor-
rect traces routing, appropriate traces widths and,
in case of high voltages, compliance with isolation
distances are the major issues. The L4990 eases
this task by putting two pins at disposal for sepa-
rate current returns of bias (SGND) and switch
drive currents (PGND) The matter is complex and
only few important points will be here reminded.
1) All current returns (signal ground, power
ground, shielding, etc.) should be routed sepa-
rately and should be connected only at a single
ground point.
2) Noise coupling can be reduced by minimizing
the area circumscribed by current loops. This
applies particularly to loops where high pulsed
currents flow.
3) For high current paths, the traces should be
doubled on the other side of the PCB whenever
possible: this will reduce both the resistance
and the inductance of the wiring.
4) Magnetic field radiation (and stray inductance)
can be reduced by keeping all traces carrying
switched currents as short as possible.
5) In general, traces carrying signal currents
should run far from traces carrying pulsed cur-
rents or with quickly swinging voltages. From
this viewpoint, particular care should be taken
of the high impedance points (current sense in-
put, feedback input, ...). It could be a good idea
to route signal traces on one PCB side and
power traces on the other side.
6) Provide adequate filtering of some crucial
points of the circuit, such as voltage refer-
ences, IC’s supply pins, etc.
APPLICATION IDEAS
Here follows a series of ideas/suggestionsaimed at
either improving performance or solving common
application problems of L4990-basedsupplies.
D97IN504
L4990
PGND
ISEN
OUT
VC
SGND
VIN
ISOLATION
BOUNDARY
10
9
13
11
12
Figure 33. Isolated MOSFET Drive & Current Transformer Sensing in 2-switch Topologies.
L4990
VREF
T
STD1NB50-1
VCC
VIN
22V
D97IN505A
2.2M
33K
SELF-SUPPLY
WINDING
8
4
12
11
47K
Figure 34. Low consumption start-up
L4990 - L4990A
18/24
相關PDF資料 |
PDF描述 |
|---|---|
| L5970AD | 1.8 A SWITCHING REGULATOR, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| L5972D013TR | 3 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, PDSO8 |
| L5972D | 3 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, PDSO8 |
| L5973AD | 2.3 A SWITCHING REGULATOR, PDSO8 |
| L5973D | 3.5 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L4991 | 功能描述:TEST COIL FOR REED SWITCH, 1PC RoHS:是 類別:開關 >> 配件 系列:- 標準包裝:100 系列:- 其它名稱:886.0007886.0007-ND |
| L4992 | 制造商:STMicroelectronics 功能描述: 制造商:STMicroelectronics 功能描述:VOLT SUPERVISOR CNTRLR 5.1V/3.3V 32TQFP - Trays |
| L4993 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low drop voltage regulator |
| L4993D | 功能描述:低壓差穩壓器 - LDO Low drop voltage regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| L4993DTR | 功能描述:低壓差穩壓器 - LDO Low drop voltage regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。