參數資料
型號： L4974A
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： 5.5 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PDIP20
封裝： POWER, PLASTIC, DIP-20
文件頁數： 17/22頁
文件大?。?/td> 6679K
代理商： L4974A
The L4974A is a 3.5A monolithic stepdown switch-
ing regulator working in continuous mode realized in
the new BCD Technology. This technology allows
the integration of isolated vertical DMOS power tran-
sistors plus mixed CMOS/Bipolar transistors.
The device can deliver 3.5A at an output voltage ad-
justable from 5.1V to 40V and contains diagnostic
and control functions that make it particularly suit-
able for microprocessor based systems.
BLOCK DIAGRAM
The block diagram shows the DMOS power tran-
sistors and the PWM control loop. Integrated func-
tions include a reference voltage trimmed to 5.1V
± 2%, soft start, undervoltage lockout, oscillator with
feedforward control, pulse by pulse current limit,
thermal shutdown and finally the reset and power
fail circuit. The reset and power fail circuit provides
an output signal for a microprocessor indicating the
status of the system.
Device turn on is around 11V with a typical 1V hys-
terysis, this threshold porvides a correct voltage for
the driving stage of the DMOS gate and the hyste-
rysis prevents instabilities.
An external bootstrap capacitor charge to 12V by an
internal voltage reference is needed to provide cor-
rect gate drive to the power DMOS. The driving cir-
cuit is able to source and sink peak currents of
around 0.5A to the gate of the DMOS transistor. A
typical switching time of the current in the DMOS
transistor is 50ns. Due to the fast commutation
switching frequencies up to 200kHz are possible.
The PWM control loop consists of a sawtooth oscil-
lator, error amplifier, comparator, latch and the out-
put stage. An error signal is produced by comparing
the output voltage with the precise 5.1V
± 2% on chip
reference. This error signal is then compared with
the sawtooth oscillator in order to generate frixed
frequency pulse width modulated drive for the out-
put stage. A PWM latch is included to eliminate
multiple pulsing within a period even in noisy envi-
ronments.
The gain and stability of the loop can be adjusted by
an external RC network connected to the output of
the error amplifier. A voltage feedforward control
has been added to the oscillator, this maintains su-
perior line regulation over a wide input voltage
range. Closing the loop directly gives an output vol-
tage of 5.1V, higher voltages are obtained by insert-
ing a voltage divider.
At turn on, output overcurrents are prevented by the
soft start function (fig. 2). The error amplifier is in-
itially clamped by an external capacitor, Css, and al-
lowed to rise linearly under the charge of an internal
constant current source.
Output overload protection is provided by a current
limit circuit. The load current is sensed by a internal
metal resistor connected to a comparator. When the
load current exceeds a preset threshold, the output
of the comparator sets a flip flop which turns off the
power DMOS. The next clock pulse, from an internal
40kHz oscillator, will reset the flip flop and the power
DMOS will again conduct. This current protection
method, ensures a constant current output when the
system is overloaded or short circuited and limits the
switching frequency, in this condition, to 40kHz. The
Reset and Power fail circuit (fig. 4), generates an
output signal when the supply voltage exceeds a
threshold programmed by an external voltage di-
vider. The reset signal, is generated with a delay
time programmed by a external capacitor on the de-
lay pin. When the supply voltage falls below the
threshold or the output voltage goes below 5V, the
reset output goes low immediately. The reset output
is an open drain.
Fig. 4A shows the case when the supply voltage is
higher than the threshold, but the output voltage is
not yet 5V.
Fig. 4B shows the case when the output is 5.1V, but
the supply voltage is not yet higher than the fixed
threshold.
The thermal protection disables circuit operation
when the junction temperature reaches about
150
°C and has a hysterysis to prevent unstable
conditions.
CIRCUIT OPERATION
L4974A
4/22
相關PDF資料
PDF描述
L4976 2.5 A SWITCHING REGULATOR, 300 kHz SWITCHING FREQ-MAX, PDIP8
L4976D013TR 2.5 A SWITCHING REGULATOR, 300 kHz SWITCHING FREQ-MAX, PDSO16
L4977A 11 A SWITCHING REGULATOR, 500 kHz SWITCHING FREQ-MAX, PZFM15
L4978D013TR 3.5 A SWITCHING REGULATOR, 300 kHz SWITCHING FREQ-MAX, PDSO16
L4978 3.5 A SWITCHING REGULATOR, 300 kHz SWITCHING FREQ-MAX, PDIP8
相關代理商/技術參數
參數描述
L4974A 制造商:STMicroelectronics 功能描述:IC SWITCHING REG 3.5A 4974 DIP20
L4974AE 制造商:STMicroelectronics 功能描述:
L4975 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5A SWITCHING REGULATOR
L4975A 功能描述:直流/直流開關調節器 5.1 to 40V Step-Down RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
L4975A 制造商:STMicroelectronics 功能描述:SWITCHING REG 5A 4975 MULTIWATT15
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*