參數資料
型號： KSZ8895MQI
廠商： Micrel Inc
文件頁數： 75/119頁
文件大?。?/td> 0K
描述： IC ETHERNET SWITCH 5PORT 128PQFP
特色產品： KSZ8895MQ Ethernet Switches
標準包裝： 66
系列： *
其它名稱： 576-3997
2011-2012 Microchip Technology Inc.
Preliminary
DS41579C-page 59
PIC16(L)F1782/3
6.2
Clock Source Types
Clock sources can be classified as external or internal.
External clock sources rely on external circuitry for the
clock source to function. Examples are: oscillator mod-
ules (EC mode), quartz crystal resonators or ceramic
resonators (LP, XT and HS modes) and Resis-
tor-Capacitor (RC) mode circuits.
Internal clock sources are contained within the oscilla-
tor module. The internal oscillator block has two inter-
nal oscillators and a dedicated Phase-Lock Loop
(HFPLL) that are used to generate three internal sys-
tem clock sources: the 16 MHz High-Frequency Inter-
nal Oscillator (HFINTOSC), 500 kHz (MFINTOSC) and
the 31 kHz Low-Frequency Internal Oscillator (LFIN-
TOSC).
The system clock can be selected between external or
internal clock sources via the System Clock Select
(SCS) bits in the OSCCON register. See Section 6.3
“Clock Switching” for additional information.
6.2.1
EXTERNAL CLOCK SOURCES
An external clock source can be used as the device
system clock by performing one of the following
actions:
Program the FOSC<2:0> bits in the Configuration
Words to select an external clock source that will
be used as the default system clock upon a
device Reset.
Write the SCS<1:0> bits in the OSCCON register
to switch the system clock source to:
- Timer1 oscillator during run-time, or
- An external clock source determined by the
value of the FOSC bits.
tion.
6.2.1.1
EC Mode
The External Clock (EC) mode allows an externally
generated logic level signal to be the system clock
source. When operating in this mode, an external clock
source
is
connected
to
the
OSC1
input.
OSC2/CLKOUT is available for general purpose I/O or
CLKOUT. Figure 6-2 shows the pin connections for EC
mode.
EC mode has 3 power modes to select from through
Configuration Words:
High power, 4-32 MHz (FOSC = 111)
Medium power, 0.5-4 MHz (FOSC = 110)
Low power, 0-0.5 MHz (FOSC = 101)
The Oscillator Start-up Timer (OST) is disabled when
EC mode is selected. Therefore, there is no delay in
operation after a Power-on Reset (POR) or wake-up
from Sleep. Because the PIC MCU design is fully
static, stopping the external clock input will have the
effect of halting the device while leaving all data intact.
Upon restarting the external clock, the device will
resume operation as if no time had elapsed.
FIGURE 6-2:
EXTERNAL CLOCK (EC)
MODE OPERATION
6.2.1.2
LP, XT, HS Modes
The LP, XT and HS modes support the use of quartz
crystal resonators or ceramic resonators connected to
OSC1 and OSC2 (Figure 6-3). The three modes select
a low, medium or high gain setting of the internal
inverter-amplifier to support various resonator types
and speed.
LP Oscillator mode selects the lowest gain setting of the
internal inverter-amplifier. LP mode current consumption
is the least of the three modes. This mode is designed to
drive only 32.768 kHz tuning-fork type crystals (watch
crystals).
XT Oscillator mode selects the intermediate gain
setting of the internal inverter-amplifier. XT mode
current consumption is the medium of the three modes.
This mode is best suited to drive resonators with a
medium drive level specification.
HS Oscillator mode selects the highest gain setting of the
internal inverter-amplifier. HS mode current consumption
is the highest of the three modes. This mode is best
suited for resonators that require a high drive setting.
Figure 6-3 and Figure 6-4 show typical circuits for
quartz crystal and ceramic resonators, respectively.
OSC1/CLKIN
OSC2/CLKOUT
Clock from
Ext. System
PIC MCU
FOSC/4 or I/O(1)
Note 1:
Output depends upon CLKOUTEN bit of the
Configuration Words.
相關PDF資料
PDF描述
KSZ8895MQ IC ETHERNET SW 5PORT 128-PQFP
KSZ8993FL IC CONV MED 10/100 SGL 128PQFP
KSZ8993MLI IC SWITCH 10/100 3PORT 128-PQFP
KSZ8993ML IC SWITCH 10/100 W/TXRX 128PQFP
KSZ8995FQ IC SWITCH 10/100 5PORT 128-PQFP
相關代理商/技術參數
參數描述
KSZ8895MQXCA 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:0°C ~ 70°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66
KSZ8895MQXIA 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:-40°C ~ 85°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66
KSZ8895RQ 功能描述:以太網 IC 5-port Switch, one SW5-RMII and one P5-RMII Interface RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8895RQ TR 功能描述:以太網 IC 5-port Switch, one SW5-RMII and one P5-RMII Interface RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8895RQ-EVAL 功能描述:以太網開發工具 5-port Switch, one SW5-RMII and one P5-RMII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*