參數資料
型號： KSZ8721CL-EVAL
廠商： Micrel Inc
文件頁數： 8/32頁
文件大小： 0K
描述： BOARD EVALUATION FOR KSZ8721CL
標準包裝： 1
主要目的： 接口，以太網 PHY
嵌入式： 否
已用 IC / 零件： KSZ8721CL
主要屬性： 1 個端口，100BASE-TX/100BASE-FX/10BASE-T
次要屬性： MII，RMII，HP 自動 MDI，MDI-X 自動極性校正
已供物品： 板
其它名稱： 576-1629
KS8721CL
Micrel
M9999-100804
16
October 2004
Power Management
The KS8721CL offers the following modes for power management:
Power-Down Mode: This mode can be achieved by writing to Register 0.11 or pulling pin 30 PD# low.
Power-Saving Mode: This mode can be disabled by writing to Register 1fh.10. The KS8721CL turns off everything
except for the Energy Detect and PLL circuits when the cable is not installed. In other words, the KS8721CL shuts
down most of the internal circuits to save power if there is no link. Power-saving mode is in the most effective state
when auto-negotiation mode is enabled.
100BT FX Mode
Please contact your local field application engineer (FAE) for a reference schematic on fiber connection.
100BT FX mode is activated when FXSD/FXEN is higher than 0.6V (this pin has a default pull down). Under this mode, the
auto-negotiation and auto-MDI-X features are disabled.
In fiber operation, the FXSD pin should connect to the signal detect (SD) output of the fiber module. The internal threshold of
FXSD is around 1/2 V
DD ±50mV (1.25V ±0.05V). Above this level, the fiber signal is considered detected. The operation is
summarized in the following table:
FXSD/FXEN
Condition
Less than 0.6V
100TX mode
Less than 1.25V,
FX mode
but greater than 0.6V
No signal detected
FEF generated
Greater than 1.25
FX mode
Signal detected
Table 1. 100BT FX Mode
To ensure proper operation, the swing of fiber module SD should cover the threshold variation. A resistive voltage divider is
recommended to adjust the SD voltage range.
FEF, repetition of a special pattern which consists of 84-one and 1-zero, is generated under “FX mode with no signal detected.”
The purpose of FEF is to notify the sender of a faulty link. When receiving an FEF, the LINK will go down to indicate a fault,
even with fiber signal detected. The transmitter is not affected by receiving an FEF and still sends out its normal transmit pattern
from MAC. FEF can be disabled by strapping pin 27 low. Refer to the “Strapping Options” section.
Media Converter Operation
The KS8721CL is capable of performing media conversion with two parts in a back-to-back RMII loop-back mode as indicated
in the diagram. Both parts are in RMII mode and with RMII BTB asserted (pins 21 and 22 strapped high). One part is operating
in TX mode and the other is operating in FX mode. Both parts can share a common 50MHz oscillator.
Under this operation, auto-negotiation on the TX side prohibits 10BASE-T link-up. Additional options can be implemented
under this operation. Disable the transmitter and set it at tri-state by controlling the high TXD2 pin. In order to do this, RXD2
and TXD2 pins need to be connected via inverter. When TXD2 pin is high in both the copper and fiber operation, it is disabled
transmit. Meanwhile, the RXD2 pin on the copper side serves as the energy detect and can indicate if a line signal is detected.
TXD3 should be tied low and RXD3 allowed to float. Please contact your Micrel FAE for a media converter reference design.
Figure 3. Fiber Module
Rx +/-
Tx +/-
FTx
FRx
Pin
34
TxD
(Fiber Mode)
21 22
Pin
21 22
50MHz
VCC
OSC
TxC/
Ref_CLK
TxC/
Ref_CLK
RxD
VCC
KS8721CL
KS8721CL
To the SD Pin of the
Fiber Module
TxD
相關PDF資料
PDF描述
MAX6429FIUR+T IC MONITOR BAT LP SOT23-3
M3AMK-4040K IDC CABLE - MSC40K/MC40F/MCG40K
M3GGK-5036J IDC CABLE - MCS50K/MC50G/MCS50K
M3FFK-5036J IDC CABLE - MCF50K/MC50G/MCF50K
MAX6429BHUR+T IC MONITOR BAT LP SOT23-3
相關代理商/技術參數
參數描述
KSZ8721SL 功能描述:以太網 IC 10/100 Base-TX/FX Physical Layer Transceiver, Single 3.3V Supply, 48-SSOP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8721SL TR 功能描述:以太網 IC 10/100 Base-TX/FX Physical Layer Transceiver, Single 3.3V Supply, 48-SSOP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8721SLA4 功能描述:TXRX 10/100 3.3V 48-SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND
KSZ8721SLA4 TR 功能描述:TRANSCEIVER 10/100 3.3V 48-SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND
KSZ8721SL-EVAL 功能描述:以太網開發工具 KSZ8721SL Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*