參數資料
| 型號： | KSZ8031RNL |
| 廠商： | Micrel Inc |
| 文件頁數： | 7/43頁 |
| 文件大小： | 0K |
| 描述： | TXRX PHY 100BASE TX 3.3V 24QFN |
| 標準包裝： | 75 |
| 類型： | PHY 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RMII |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-QFN（4x4） |
| 包裝： | 管件 |
| 配用： | 576-3862-ND - BOARD EVALUATION FOR KSZ8031RNL |
| 其它名稱： | 576-3741-5 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
Micrel, Inc.
KSZ8021RNL / KSZ8031RNL
August 2010
15
M9999-082710-1.0
RMII Data Interface
The Reduced Media Independent Interface (RMII) specifies a low pin count Media Independent Interface (MII). It provides
a common interface between physical layer and MAC layer devices, and has the following key characteristics:
Pin count is 8 pins (3 pins for data transmission, 4 pins for data reception, 1 pin for the 50MHz reference clock).
10Mbps and 100Mbps data rates are supported at both half and full duplex.
Data transmission and reception are independent and belong to separate signal groups.
Transmit data and receive data are each 2-bit wide, a dibit.
RMII Signal Definition
The following table describes the RMII signals. Refer to RMII Specification v1.2 for detailed information.
RMII
Signal Name
Direction
(with respect to PHY,
KSZ8021/31RNL signal)
Direction
(with respect to
MAC)
Description
REF_CLK
Output (25MHz Clock Mode) /
<no connect> (50MHz Clock
Mode)
Input /
Input or <no connect>
Synchronous 50MHz reference clock for
receive, transmit and control interface
TXEN
Input
Output
Transmit Enable
TXD[1:0]
Input
Output
Transmit Data [1:0]
CRS_DV
Output
Input
Carrier Sense/Receive Data Valid
RXD[1:0]
Output
Input
Receive Data [1:0]
RXER
Output
Input, or (not
required)
Receive Error
Table 1. RMII Signal Description
Reference Clock (REF_CLK)
REF_CLK is a continuous 50MHz clock that provides the timing reference for TXEN, TXD[1:0], CRS_DV, RXD[1:0], and
RXER.
For RMII – 25MHz Clock Mode, the KSZ8021/31RNL generates and outputs the 50MHz RMII REF_CLK to the MAC at
REF_CLK (Pin 16).
For RMII – 50MHz Clock Mode, the KSZ8021/31RNL takes in the 50MHz RMII REF_CLK from the MAC or system board
at XI (Pin 8) and has the REF_CLK (pin 16) left as a no connect.
Transmit Enable (TXEN)
TXEN indicates that the MAC is presenting dibits on TXD[1:0] for transmission. It is asserted synchronously with the first
dibit of the preamble and remains asserted while all dibits to be transmitted are presented on the RMII, and is negated
prior to the first REF_CLK following the final dibit of a frame.
TXEN transitions synchronously with respect to REF_CLK.
Transmit Data [1:0] (TXD[1:0])
TXD[1:0] transitions synchronously with respect to REF_CLK. When TXEN is asserted, TXD[1:0] are accepted for
transmission by the PHY.
TXD[1:0] is ”00” to indicate idle when TXEN is de-asserted. Values other than “00” on TXD[1:0] while TXEN is de-asserted
are ignored by the PHY.
Carrier Sense/Receive Data Valid (CRS_DV)
CRS_DV is asserted by the PHY when the receive medium is non-idle. It is asserted asynchronously on detection of
carrier. This is when squelch is passed in 10Mbps mode, and when two non-contiguous zeroes in 10 bits are detected in
100Mbps mode. Loss of carrier results in the de-assertion of CRS_DV.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J5Z-EY-F1 | CONVERTER MOD DC/DC 2V 20W |
| VE-J5X-MX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| MS27468E23F53S | CONN RCPT 53POS JAM NUT W/SCKT |
| VE-J5X-MX-F3 | CONVERTER MOD DC/DC 5.2V 75W |
| KSZ8021RNL | TXRX PHY 100BASE TX 3.3V 24QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8031RNL TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ RMII Support (24-QFN) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8031RNL-EVAL | 功能描述:以太網開發工具 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ RMII Support (24-QFN) - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8031RNLI | 功能描述:TXRX PHY 10/100 3.3V 24-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KSZ8031RNLI TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ RMII Support (24-QFN, Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8031RNLITR | 制造商:Micrel Inc 功能描述:Ethernet transceiver,PHY,RMII,QFN24 |
發布緊急采購，3分鐘左右您將得到回復。