- 您現在的位置：買賣IC網 > PDF目錄9696 > KS8001L (Micrel Inc)TXRX 10/100 LINKMD 3.3V 48-LQFP PDF資料下載
參數資料
| 型號： | KS8001L |
| 廠商： | Micrel Inc |
| 文件頁數： | 5/44頁 |
| 文件大小： | 0K |
| 描述： | TXRX 10/100 LINKMD 3.3V 48-LQFP |
| 標準包裝： | 250 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | MII，RMII，SMII |
| 電源電壓： | 3.14 V ~ 3.47 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
| 配用： | KS8001L-EVAL-ND - EVAL KIT EXPERIMENTAL KS8001L |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
KS8001
Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
13
SQE and Jabber Function (10BASE-T only)
In 10BASE-T operation, a short pulse will be put out on the COL pin after each packet is transmitted. This is required as a test of the
10BASE-T transmit/receive path and is called SQE test. The 10BASE-T transmitter will be disabled and COL will go high if TXEN is
High for more than 20 ms (Jabbering). If TXEN then goes low for more than 250 ms, the 10BASE-T transmitter will be re-enabled
and COL will go Low.
Auto-Negotiation
The KS8001 performs auto-negotiation by hardware strapping option (pin 29) or software (Register 0.12). It will automatically
choose its mode of operation by advertising its abilities and comparing them with those received from its link partner whenever auto-
negotiation is enabled. It can also be configured to advertise 100BASE-TX or 10BASE-T in either full- or half-duplex mode. Auto-
negotiation is disabled in FX mode.
During auto-negotiation, the contents of Register 4, coded in Fast Link Pulse (FLP), will be sent to its link partner under the
conditions of power-on, link-loss or re-start. At the same time, the KS8001 will monitor incoming data to determine its mode of
operation. Parallel detection circuit will be enabled as soon as either 10BASE-T NLP (Normal Link Pulse) or 100BASE-TX idle is
detected. The operation mode is configured based on the following priority:
Priority 1: 100BASE-TX, full-duplex
Priority 2: 100BASE-TX, half-duplex
Priority 3: 10BASE-T, full-duplex
Priority 4: 10BASE-T, half-duplex
When the KS8001 receives a burst of FLP from its link partner with 3 identical link code words (ignoring acknowledge bit), it will store
these code words in Register 5 and wait for the next 3 identical code words. Once the KS8001 detects the second code words, it
then configures itself according to the above-mentioned priority. In addition, the KS8001 also checks for 100BASE-TX idle or
10BASE-T NLP symbols. If either is detected, the KS8001 automatically configures to match the detected operating speed.
MII Management Interface
The KS8001 supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input / Output (MDIO)
Interface. This interface allows upper-layer devices to monitor and control the state of the KS8001. The MDIO interface consists of
the following:
A physical connection including a data line (MDIO), a clock line (MDC) and an optional interrupt line (INTRPT)
A specific protocol that runs across the above-mentioned physical connection and it also allows one controller to
communicate with multiple KS8001 devices. Each KS8001 is assigned an MII address between 0 and 31 by the PHYAD
inputs.
An internal addressable set of fourteen 16-bit MDIO registers. Register [0:6] are required and their functions are specified
by the IEEE 802.3 specifications. Additional registers are provided for expanded functionality.
The INTPRT pin functions as a management data interrupt in the MII. An active Low or High in this pin indicates a status change on
the KS8001 based upon 1fh.9 level control. Register bits at 1bh[15:8] are the interrupt enable bits. Register bits at 1bh[7:0] are the
interrupt condition bits. This interrupt is cleared by reading Register 1bh.
MII Data Interface
The data interface consists of separate channels for transmitting data from a 10/100 802.3 compliant Media Access Controller (MAC)
to the KS8001, and for receiving data from the line. Normal data transmission is implemented in 4B Nibble Mode (4-bit wide
nibbles).
Transmit Clock (TXC): The transmit clock is normally generated by the KS8001 from an external 25MHz reference source at the
X1 input. The transmit data and control signals must always be synchronized to the TXC by the MAC. The KS8001 normally
samples these signals on the rising edge of the TXC.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J7Z-EY-F4 | CONVERTER MOD DC/DC 2V 20W |
| MC14490DWR2 | IC ELIMINATOR BOUNCE HEX 16-SOIC |
| MS27499E18B32SA | CONN RCPT 32POS BOX MNT W/SCKT |
| VE-27L-MX-F2 | CONVERTER MOD DC/DC 28V 75W |
| MS27497T18B32SB | CONN RCPT 32POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KS8001L-EVAL | 功能描述:EVAL KIT EXPERIMENTAL KS8001L RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| KS8001LI | 功能描述:TXRX 10/100 LINKMD 3.3V 48-LQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KS8001S | 功能描述:TXRX 10/100 LINKMD 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KS8001S TR | 功能描述:TXRX 10/100 LINKMD 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KS8001SI | 功能描述:TXRX 10/100 LINKMD 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
發布緊急采購，3分鐘左右您將得到回復。