- 您現在的位置：買賣IC網 > PDF目錄373177 > KS16112 (SAMSUNG SEMICONDUCTOR CO. LTD.) CAP 33PF 50V 5% NPO(C0G) SMD-0603 TR-7-PA PDF資料下載
參數資料
| 型號： | KS16112 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | CAP 33PF 50V 5% NPO(C0G) SMD-0603 TR-7-PA |
| 中文描述： | 14400分之9600基點傳真調制解調器 |
| 文件頁數： | 22/69頁 |
| 文件大?。?/td> | 513K |
| 代理商： | KS16112 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
KS16112/4
9600/14400 bps FAX MODEM
-
22
-
When AHEOF is set while in HDLC transmit mode, the modem automatically generates and transmits the
FCS ( frame check sequence ) and at least one closing flag upon detecting an underrun condition in the
transmission of data. AHEOF is valid only when the modem is configured for HDLC mode ( HDLCE is set ).
Buffer Data Available No.2
1E : 0 ( - )
When BDA1 has been set by the modem, the modem has either written or read buffer data to/from the
YDL1 register. The setting of the BDA1 bit can be setup to cause an IRQ interrupt ( see INTE1 and
INTA1 bit descriptions ). When the host microprocessor reads or writes the YDL1 register, the modem
automatically resets the BDA1 bit.
BDA 1
Buffer Data Available No.1
1E : 3 ( - )
When BDA2 has been set by the modem and the modem is in parallel data mode ( PDME is set ), with
or without HDLC enabled, transmit data has been read from DBFR by the modem ( transmit mode ) or
received data has been written by the modem into DBFR ( receive mode ). When the modem is in serial
mode ( PDME is reset ), the modem sets BDA2 whenever data has been read from or written into YDL2.
The setting of the BDA2 bit can be setup to cause an IRQ interrupt ( see INTE2 and INTA2 bit descrip -
tions ). When the host microprocessor reads or writes the YDL2/DBFR register, the modem automatically
resets the BDA2 bit.
BRT 1
Baud Rate 1
05 : 2 ( 1 )
When BRT1 is set, RAM access for ADR1 takes place at the baud rate ( the baud rate depends on the se -
lected configuration ), otherwise it occurs at the sample rate ( 9600Hz ). This bit must be zero in FSK, Tone
or DTMF receive modes.
BRT 2
Baud Rate 2
15 : 2 ( 0 )
When BRT2 is set RAM access for ADR2 takes place at the baud rate ( the baud rate depends on the se -
lected configuration ). Otherwise it occurs at the sample rate ( 9600Hz ). This bit must be zero in FSK, Tone
or DTMF receive modes.
CASC
Select 12th Order Filter Cascade
08 : 4 ( 0 )
When CASC is set, the tone detectors are cascaded to form one 12th order filter ( TD3 is the output status
bit for the 12th order filter cascade ). When CASC is reset, the three tone detectors operate as three parallel
independent 4th order filters. The 12th order mode is only valid in the FSK , FSK and DTMF receiver
modes when RTS is off and RTSB is reset.
AHEOF
Automatic HDLC End of Frame
15 : 5 ( 0 )
BDA 2
相關PDF資料 |
PDF描述 |
|---|---|
| KS16116-02 | 9600 bps FAX MODEM(9600bps傳真調制解調器) |
| KS16117-02 | 14400 bps FAX MODEM(14400bps傳真調制解調器) |
| KS16118 | 9600bps FAX super one-chip(9600bps傳真調制解調器) |
| KS16120B | DSP for Digital Answering Phone(用于數字應答電話的DSP) |
| KS16121 | DSP for Digital Answering Phone(用于數字應答電話的DSP) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KS16114 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:9600/14400 bps FAX MODEM |
| KS16-14 | 制造商:MAJOR 功能描述: |
| KS-16287L1 | 制造商:WSTELC 功能描述: |
| KS-16287L2 | 制造商:WSTELC 功能描述: |
| KS16390 | 制造商: 功能描述: 制造商:Cornell Dubilier Electronics 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。