參數資料
型號: KMPC885VR80
廠商: Freescale Semiconductor
文件頁數: 8/87頁
文件大小: 0K
描述: IC MPU POWERQUICC 80MHZ 357PBGA
標準包裝: 2
系列: MPC8xx
處理器類型: 32-位 MPC8xx PowerQUICC
速度: 80MHz
電壓: 3.3V
安裝類型: 表面貼裝
封裝/外殼: 357-BBGA
供應商設備封裝: 357-PBGA(25x25)
包裝: 托盤
MPC885/MPC880 PowerQUICC Hardware Specifications, Rev. 7
16
Freescale Semiconductor
Layout Practices
Figure 5. Example Voltage Sequencing Circuit
9
Layout Practices
Each VDD pin on the MPC885/MPC880 should be provided with a low-impedance path to the board’s
supply. Each GND pin should likewise be provided with a low-impedance path to ground. The power
supply pins drive distinct groups of logic on chip. The VDD power supply should be bypassed to ground
using at least four 0.1 F by-pass capacitors located as close as possible to the four sides of the package.
Each board designed should be characterized and additional appropriate decoupling capacitors should be
used if required. The capacitor leads and associated printed-circuit traces connecting to chip VDD and
GND should be kept to less than half an inch per capacitor lead. At a minimum, a four-layer board
employing two inner layers as VDD and GND planes should be used.
All output pins on the MPC885/MPC880 have fast rise and fall times. Printed-circuit (PC) trace
interconnection length should be minimized in order to minimize undershoot and reflections caused by
these fast output switching times. This recommendation particularly applies to the address and data buses.
Maximum PC trace lengths of six inches are recommended. Capacitance calculations should consider all
device loads as well as parasitic capacitances due to the PC traces. Attention to proper PCB layout and
bypassing becomes especially critical in systems with higher capacitive loads because these loads create
higher transient currents in the VDD and GND circuits. Pull up all unused inputs or signals that will be
inputs during reset. Special care should be taken to minimize the noise levels on the PLL supply pins. For
more information, please refer to the MPC885 PowerQUICC Family Reference Manual, Section 14.4.3,
“Clock Synthesizer Power (VDDSYN, VSSSYN, VSSSYN1).”
10 Bus Signal Timing
The maximum bus speed supported by the MPC885/MPC880 is 80 MHz. Higher-speed parts must be
operated in half-speed bus mode (for example, an MPC885/MPC880 used at 133 MHz must be configured
for a 66 MHz bus). Table 7 shows the frequency ranges for standard part frequencies in 1:1 bus mode, and
Table 8 shows the frequency ranges for standard part frequencies in 2:1 bus mode.
VDDH
VDDL
1N5820
MUR420
相關PDF資料
PDF描述
KMPC885VR66 IC MPU POWERQUICC 66MHZ 357PBGA
KMPC885VR133 IC MPU POWERQUICC 133MHZ 357PBGA
HSC50DTEN CONN EDGECARD 100POS .100 EYELET
KMPC885CZP66 IC MPU POWERQUICC 66MHZ 357PBGA
KMPC885CZP133 IC MPU POWERQUICC 133MHZ 357PBGA
相關代理商/技術參數
參數描述
KMPC885ZP133 功能描述:微處理器 - MPU PQ I HIP6W DUET RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
KMPC885ZP66 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Hardware Specifications
KMPC885ZP80 功能描述:微處理器 - MPU PQ I HIP6W DUET RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
KMPG666-4 制造商:Kingstate Electronics Corporation 功能描述:
KMQ100VB102M18X35LL 功能描述:鋁質電解電容器 - 帶引線 1000UF 100V RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk