參數資料
型號: KM4121
廠商: Fairchild Semiconductor Corporation
英文描述: 0.2mA, Low Cost, +2.7V & +5V, 35MHz Rail-to-Rail Amplifiers
中文描述: 0.2毫安,低成本,2.7
文件頁數: 6/10頁
文件大?。?/td> 151K
代理商: KM4121
6
REV. 1B June 2001
General Description
The KM4111 is a single supply, general purpose, voltage-
feedback amplifier fabricated on a complementary
bipolar process. The KM4111 offers 35MHz unity gain
bandwidth, 27V/
μ
s slew rate, and only 208
μ
A supply
current. It features a rail-to-rail output stage and is
unity gain stable.
The design utilizes a patent pending topology that
provides increased slew rate performance. The common
mode input range extends to 300mV below ground
and to 1.2V below Vs. Exceeding these values will not
cause phase reversal. However, if the input voltage
exceeds the rails by more than 0.5V, the input ESD
devices will begin to conduct. The output will stay at
the rail during this overdrive condition.
The design uses a Darlington output stage. The out-
put stage is short circuit protected and offers
soft
saturation protection that improves recovery time.
The typical circuit schematic is shown in Figure 1.
Figure 1: Typical Configuration
Enable/Disable Function (KM4121)
The KM4121 offers an active-low disable pin that can
be used to lower its supply current. Leave the pin
floating to enable the part. Pull the disable pin to the
negative supply (which is ground in a single supply
application) to disable the output. During the disable
condition, the nominal supply current will drop to
below 40
μ
A and the output will be at high impedance
with about 2pF capacitance.
Power Dissipation
The maximum internal power dissipation allowed is
directly related to the maximum junction tempera-
ture. If the maximum junction temperature exceeds
150
°
C, some reliability degradation will occur. If the
maximum junction temperature exceeds 175
°
C for an
extended time, device failure may occur.
The KM4111 is short circuit protected. However, this
may not guarantee that the maximum junction
temperature (+150
°
C) is not exceeded under all
conditions. Follow the maximum power derating
curves shown in Figure 2 to ensure proper operation.
Figure 2: Power Derating Curves
Overdrive Recovery
For an amplifier, an overdrive condition occurs when
the output and/or input ranges are exceeded. The
recovery time varies based on whether the input or
output is overdriven and by how much the ranges are
exceeded. The KM4111 will typically recover in less
than 20ns from an overdrive condition. Figure 3 shows
the KM4111 in an overdriven condition.
Figure 3: Overdrive Recovery
Driving Capacitive Loads
A small series resistance (R
s
) at the output of the
amplifier, illustrated in Figure 4, will improve stability
and settling performance.
+
KM4111
-
R
f
0.01
μ
F
6.8
μ
F
+
Out
In
+V
s
R
g
Maximum Power Dissipation
M
Ambient Temperature ( C)
-50
-30
-10
10
30
50
70
90
0
0.5
1.0
1.5
2.0
SO
T
23-6
l
ea
d
SO
T
23-5
l
ea
d
O
I
Time (1
μ
s/div)
Input
Output
DATA SHEET
KM4111/KM4121
相關PDF資料
PDF描述
KM4112 70A, Low Cost, +2.7V & +5V, 7.3MHz Rail-to-Rail Amplifier
KM41256AJ-10 256K X 1 Bit Dynamic RAM with Page / Nibble Mode
KM41256AJ-12 256K X 1 Bit Dynamic RAM with Page / Nibble Mode
KM41256AJ-15 256K X 1 Bit Dynamic RAM with Page / Nibble Mode
KM41256AP-10 256K X 1 Bit Dynamic RAM with Page / Nibble Mode
相關代理商/技術參數
參數描述
KM4121IT6TR3 功能描述:高速運算放大器 RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
KM41256-10P 制造商:Samsung Electro-Mechanics 功能描述:IC,DRAM,PAGE MODE,256KX1,MOS,DIP,16PIN,PLASTIC
KM41256-12PH 制造商:SAMSUNG/97'S 功能描述:41256P-12H
KM41256-15P 制造商:Samsung Semiconductor 功能描述:41256-15
KM41256-15PH 制造商:Samsung Semiconductor 功能描述:41256P-15H