• <small id="xfmyh"><output id="xfmyh"><center id="xfmyh"></center></output></small>
  • <small id="xfmyh"><output id="xfmyh"></output></small>
    <dl id="xfmyh"><dfn id="xfmyh"></dfn></dl>
    <small id="xfmyh"><div id="xfmyh"></div></small>
            
    
    
    參數資料
    型號: KM4110
    廠商: Fairchild Semiconductor Corporation
    英文描述: 0.5mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers
    中文描述: 0.5毫安,低成本,2.7
    文件頁數: 7/11頁
    文件大?。?/td> 288K
    代理商: KM4110
    KM4110/KM4120
    DATA SHEET
    REV. 1A February 2001
    7
    General Description
    The KM4110 is a single supply, general purpose, volt-
    age-feedback amplifier fabricated on a complementary
    bipolar process. The KM4110 offers 75MHz unity gain
    bandwidth, 50V/
    μ
    s slew rate, and only 505
    μ
    A supply
    current. It features a rail-to-rail output stage and is
    unity gain stable.
    The design utilizes a patent pending topology that
    provides increased slew rate performance. The common
    mode input range extends to 300mV below ground
    and to 1.2V below Vs. Exceeding these values will not
    cause phase reversal. However, if the input voltage
    exceeds the rails by more than 0.5V, the input ESD
    devices will begin to conduct. The output will stay at
    the rail during this overdrive condition.
    The design uses a Darlington output stage. The out-
    put stage is short circuit protected and offers
    soft
    saturation protection that improves recovery time.
    The typical circuit schematic is shown in Figure 1.
    Figure 1: Typical Configuration
    For optimum response at a gain of +2, a feedback resistor
    of 1k
    is recommended. Figure 2 illustrates the
    KM4110 frequency response with both 1k
    and 2k
    feedback resistors.
    Enable/Disable Function (KM4120)
    The KM4120 offers an active-low disable pin that can
    be used to lower its supply current. Leave the pin
    floating to enable the part. Pull the disable pin to the
    negative supply (which is ground in a single supply
    application) to disable the output. During the disable
    condition, the nominal supply current will drop to
    below 30
    μ
    A and the output will be at high impedance
    with about 2pF capacitance.
    Figure 2: Frequency Response vs. R
    f
    Power Dissipation
    The maximum internal power dissipation allowed is
    directly related to the maximum junction temperature.
    If the maximum junction temperature exceeds 150
    °
    C,
    some reliability degradation will occur. If the maximum
    junction temperature exceeds 175
    °
    C for an extended
    time, device failure may occur.
    The KM4110 is short circuit protected. However, this
    may not guarantee that the maximum junction tem-
    perature (+150
    °
    C) is not exceeded under all condi-
    tions. Follow the maximum power derating curves
    shown in Figure 3 to ensure proper operation.
    Figure 3: Power Derating Curves
    Overdrive Recovery
    For an amplifier, an overdrive condition occurs when
    the output and/or input ranges are exceeded. The
    recovery time varies based on whether the input or
    output is overdriven and by how much the ranges are
    exceeded. The KM4110 will typically recover in less
    than 20ns from an overdrive condition. Figure 4
    shows the KM4110 in an overdriven condition.
    +
    KM4110
    -
    R
    f
    0.01
    μ
    F
    6.8
    μ
    F
    +
    Out
    In
    +V
    s
    R
    g
    M
    Frequency (MHz)
    0.1
    1
    10
    100
    G = 2
    R
    L
    = 1k
    R
    f
    = 1k
    R
    f
    = 2k
    M
    Ambient Temperature ( C)
    -50
    -30
    -10
    10
    30
    50
    70
    90
    SOIC-8 lead
    0
    0.5
    1.0
    1.5
    2.0
    SOT23-5 lead
    相關PDF資料
    PDF描述
    KM4120 0.5mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers
    KM4111 0.2mA, Low Cost, +2.7V & +5V, 35MHz Rail-to-Rail Amplifiers
    KM4121 0.2mA, Low Cost, +2.7V & +5V, 35MHz Rail-to-Rail Amplifiers
    KM4112 70A, Low Cost, +2.7V & +5V, 7.3MHz Rail-to-Rail Amplifier
    KM41256AJ-10 256K X 1 Bit Dynamic RAM with Page / Nibble Mode
    相關代理商/技術參數
    參數描述
    KM4110IT5 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:0.5mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers
    KM4110IT5TR3 功能描述:運算放大器 - 運放 0.5ma 75Mhz RRO amplifier RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
    KM4111 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:0.2mA, Low Cost, +2.7V & +5V, 35MHz Rail-to-Rail Amplifiers
    KM4111IT5TR3 功能描述:高速運算放大器 0.2ma 35Mhz RRO amplifier RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
    KM4112 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:70A, Low Cost, +2.7V & +5V, 7.3MHz Rail-to-Rail Amplifier