參數資料
型號： KITMPR084EVM
廠商： Freescale Semiconductor
文件頁數： 15/40頁
文件大小： 0K
描述： KIT EVAL 8-PAD TOUCH MPR084
標準包裝： 1
傳感器類型： 觸摸，電容式
接口： I²C
電源電壓： 1.8 V ~ 3.6 V
嵌入式： 是，其它
已供物品： 板，纜線，CD
已用 IC / 零件： MPR084
產品目錄頁面： 2808 (CN2011-ZH PDF)
相關產品： MPR084EJR2CT-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR084QR2-ND - IC CTLR TOUCH SENSOR PROX 16-QFN
MPR084Q-ND - IC CTLR TOUCH SENSOR PROX 16-QFN
MPR084EJR2TR-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR084EJ-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR084
Sensors
22
Freescale Semiconductor
7Interrupts
7.1
Introduction
The MPR084 has one interrupt output that is configured by registers and alerts the application when a touch or fault is detected.
When running in Run2 or Stop2 mode where I2C communication is not available this feature alerts the user to sensor touches.
7.2
Condition for Interrupt
There are two cases that latch the Interrupt buffered data available or fault detected.
7.2.1
Buffered Data Available
The interrupt for Buffered Data Available will only trigger when the NDF (No Data Flag) transitions from high to low. This signifies
that there is new data available in the buffer. The interrupt is deasserted on the first read/write of the FIFO Register and cannot
be reasserted for buffered data until the FIFO is empty (either by reading all the data, or clearing the buffer).
7.2.2
Fault Detected
The interrupt for a Fault Detected condition is triggered any time the Fault condition in the Fault Register transitions from zero to
non-zero. The interrupt is deasserted when the Fault Register is cleared (by writing to the Fault Register).
7.3
Settings
Interrupts are configured through I2C using the Configuration Register (Section 4.7). Two of the settings in this register will affect
the interrupt functionality.
The Interrupt Enable (IRQEN) must be set high for the IRQ to be enabled. When low, all interrupts will be ignored, and the IRQ
pin will never latch.
The Interrupt Rate (IRQR) sets the minimum delay between sequential triggered interrupts. The minimum interrupt period can be
calculated by taking the product of the MCP (master clock period) and IRQR with a factor of 4. Thus, for the minimum setting an
interrupt would be triggered no more often than 4 times the sensor scan rate.
Equation 4
If the MPR084 is using Run2, the minimum interrupt period would be represented by the following equation.
Equation 5
7.4
IRQ Pin
The IRQ pin is an open-drain, latching interrupt output which requires an external pull-up resistor. The pin will latch down based
on the conditions in Section 6.2. The pin will reset when an I2C transmission reads/writes the appropriate register displaying
information about the source of the interrupt. Thus if the source is buffered data available then a FIFO Buffer read/write will clear
the IRQ pin. If the source is a fault detected then a write of the Fault Register will clear the pin.
MinInterruptPeriod ms
MCP
IRQR
4
=
MinInterruptPeriod ms
MTP
5
+
8
----------------------
1
+
8
I
RQR 4
=
相關PDF資料
PDF描述
MIC4467ZN IC DRIVER MOSF QUAD 1.2A 14-DIP
MIC4467ZWM IC DRIVER MOSF QUAD 1.2A 16-SOIC
MIC4468ZWM IC DRIVER MOSF QUAD 1.2A 16SOIC
ECM11DSEF CONN EDGECARD 22POS .156 EYELET
C8051F560DK KIT DEVELOPMENT FOR C8051F560
相關代理商/技術參數
參數描述
KITMPR121EVM 功能描述:觸摸傳感器開發工具 MPR121 Sensor Tool Box RoHS:否 制造商:Cypress Semiconductor 工具用于評估: 接口類型: 工作電壓: 最大工作溫度:
KITMPR121EVM 制造商:Freescale Semiconductor 功能描述:Sensor Toolbox Proximity Sensor Kit
KITMPVZ5004EVK 功能描述:壓力傳感器開發工具 WATER LEVEL BOARD RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度:
KITMPXA6115AEVB 功能描述:壓力傳感器開發工具 Sensor Toolbx Pressu Sensor Developmt brd RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度:
KITMPXSHOWEVK 功能描述:壓力傳感器開發工具 PRESSURE SHOWBOARD RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*