- 您現在的位置：買賣IC網 > PDF目錄374334 > KH300 (Fairchild Semiconductor Corporation) Wideband, High-Speed Operational Amplifier PDF資料下載
參數資料
| 型號： | KH300 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Wideband, High-Speed Operational Amplifier |
| 中文描述： | 寬帶，高速運算放大器 |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 94K |
| 代理商： | KH300 |
KH300
DATA SHEET
REV. 1A February 2001
5
Layout Considerations
To assure optimum performance the user should follow
good layout practices which minimize the unwanted
coupling of signals between nodes. During initial bread-
boarding of the circuit, use direct point to point wiring,
keeping lead lengths to less than 0.25
”
.The use of
solid, unbroken ground plane is helpful. Avoid wire-wrap
type pc boards and methods. Sockets with small, short
pin receptacles may be used with minimal performance
degradation although their use is not recommended.
Figure 1: Recommended Non-inverting Gain Circuit
Figure 2: Recommended Inverting Gain Circuit
During pc board layout keep all traces short and direct.
R
f
and R
g
should be as close as possible to pin 8 to
minimize capacitance at that point. For the same reason,
remove ground plane from the vicinity of pins 8 and 6. In
other areas, use as much ground plane as possible on
one side of the pc board. It is especially important to
provide a ground return path for current from the load
resistor to the power supply bypass capacitors. Ceramic
capacitors of 0.01 to 0.1
μ
F should be close to pins 13
and 16. Larger tantalum capacitors should also be
placed within one inch of these pins. To prevent signal
distortion caused by reflections from impedance mis-
matches, use terminated microstrip or coaxial cable
when the signal must traverse more than a few inches.
Since the pc board forms such an important part of the
circuit, much time can be saved if prototype boards of
any high frequency sections are built and tested early in
the design phase.
Controlling Bandwidth and Passband Response
As with any op amp, the ratio of the two feedback resistors
R
f
and R
g
, determines the gain of the KH300. Unlike
conventional op amps, however, the closed loop pole-
zero response of the KH300 is affected very little by the
value of R
g
. R
g
scales the magnitude of the gain, but
does not change the value of the feedback. R
f
does
influence the feedback and so the KH300 has been
internally compensated for optimum performance with
R
f
= 1500
, but any value of R
f
> 500
may be used
with a single capacitor placed between pins 8 and 12 for
compensation. See table 1. As R
f
decreases, C
c
must
increase to maintain flat gain. Large values of R
f
and
C
c
can be used together or separately to reduce the
bandwidth. This may be desirable for reducing the noise
bandwidth in applications not requiring the full frequency
response available.
Table 1: Bandwidth vs. R
f
and C
c
(A
v
= +20)
R
f
C
c
(pF)
f
±0.3dB
(MHz)
f
-3.0dB
(MHz)
(K
)
10.0
5.0
2.0
1.5
1.0
0.75
0.50
0
0
0
0
2
3
8
45
90
95
110
5
12
40
85
115
130
135
0.3
1.1
1.9
Low Gain Operation
The small amount of stray capacitance present at the
inverting input can cause peaking which increases with
decreasing gain. The gain setting resistor R
g
is effectively
in parallel with this capacitance and so a frequency
domain pole results. With small R
g
(Gain > 8), this pole
is at a high frequency and it affects the closed loop gain
of the KH300 only slightly. At lower values of gain, this
pole becomes significant. For example, at a gain of +2,
the gain may peak as much as 3dB at 75MHz, and have
a bandwidth exceeding 150MHz. The same behavior
does not exist for low inverting gains, however, since the
inverting input is a virtual ground which maintains a
constant voltage across the stray capacitance. Even at
inverting gains << 1, the frequency response remains
unchanged.
0.01
μ
F
22
μ
F
-15
24
KH300
-
13
+
8
R
i
50
6
V
in
R
L
50
1/2 V
o
16
11
+15
22
μ
F
0.01
μ
F
12
R
g
R
o
50
Av = 1 +
R
f
= 1500
(internal)
R
f
R
g
0.01
μ
F
22
μ
F
-15
24
KH300
-
13
+
R
i
50
V
in
R
L
50
1/2 V
o
16
11
+15
22
μ
F
0.01
μ
F
12
6
51
8
R
g
R
o
50
-Av =
R
f
= 1500
(internal)
R
f
R
g
For Z
in
= 50
Select:
R
g
||R
i
= 50
相關PDF資料 |
PDF描述 |
|---|---|
| KH560 | Wideband, Low Distortion Driver Amplifier |
| KH561 | Wideband, Low Distortion Driver Amplifier |
| KH561AI | Wideband, Low Distortion Driver Amplifier |
| KH561AM | Wideband, Low Distortion Driver Amplifier |
| KHB2442A01 | DIELECTRIC BAND PASS FILTER (TYPICAL PASSBAND CHARACTERISTIC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KH-300 | 制造商:WALDOM ELECTRONICS 功能描述: |
| KH300A | 功能描述:運算放大器 - 運放 OP AMP HI-SPEED 3000V/us 85MHz 100mA RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| KH-300-C | 制造商:WALDOM ELECTRONICS 功能描述: 制造商:GC Electronics 功能描述: 制造商:Waldom Electronics 功能描述: |
| KH30-16-10PN | 制造商:ITT Interconnect Solutions 功能描述:KH30-16-10PN - Bulk |
| KH30-16-3PN | 制造商:ITT Interconnect Solutions 功能描述:KH30-16-3PN - Bulk |
發布緊急采購，3分鐘左右您將得到回復。