- 您現在的位置：買賣IC網 > PDF目錄9979 > KAD5512P-17Q48 (Intersil)IC ADC 12BIT 170MSPS SGL 48-QFN PDF資料下載
參數資料
| 型號： | KAD5512P-17Q48 |
| 廠商： | Intersil |
| 文件頁數： | 14/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 170MSPS SGL 48-QFN |
| 產品培訓模塊： | High-Speed Analog-to-Digital Converters |
| 標準包裝： | 1 |
| 系列： | FemtoCharge™ |
| 位數： | 12 |
| 采樣率（每秒）： | 170M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 253mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-QFN（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 1 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
KAD5512P
21
FN6807.4
October 1, 2010
This relationship shows the SNR that would be achieved
if clock jitter were the only non-ideal factor. In reality,
achievable SNR is limited by internal factors such as
linearity, aperture jitter and thermal noise. Internal
aperture jitter is the uncertainty in the sampling instant
shown in Figure 3. The internal aperture jitter combines
with the input clock jitter in a root-sum-square fashion,
since they are not statistically correlated, and this
determines the total jitter in the system. The total jitter,
combined with other noise sources, then determines the
achievable SNR.
Voltage Reference
A temperature compensated voltage reference provides the
reference charges used in the successive approximation
operations. The full-scale range of each A/D is proportional
to the reference voltage. The voltage reference is internally
bypassed and is not accessible to the user.
Digital Outputs
Output data is available as a parallel bus in
LVDS-compatible or CMOS modes. Additionally, the data
can be presented in either double data rate (DDR) or
single data rate (SDR) formats. The even numbered data
output pins are active in DDR mode in the 72 pin
package option. When CLKOUT is low the MSB and all
odd logical bits are output, while on the high phase the
LSB and all even logical bits are presented (this is true in
both the 72 pin and 48 pin package options). Figures 3
and 4 show the timing relationships for LVDS/CMOS and
DDR/SDR modes.
The 48-QFN package option contains six LVDS data
output pin pairs, and therefore can only support DDR
mode.
Additionally, the drive current for LVDS mode can be set
to a nominal 3mA or a power-saving 2mA. The lower
current setting can be used in designs where the receiver
is in close physical proximity to the ADC. The applicability
of this setting is dependent upon the PCB layout,
therefore the user should experiment to determine if
performance degradation is observed.
The output mode and LVDS drive current are selected via
the OUTMODE pin as shown in Table 2.
The output mode can also be controlled through the SPI
port, which overrides the OUTMODE pin setting. Details
on this are contained in “Serial Peripheral Interface” on
An external resistor creates the bias for the LVDS drivers.
A 10kΩ, 1% resistor must be connected from the RLVDS
pin to OVSS.
Over Range Indicator
The over range (OR) bit is asserted when the output
code reaches positive full-scale (e.g. 0xFFF in offset
binary mode). The output code does not wrap around
during an over-range condition. The OR bit is updated at
the sample rate.
Power Dissipation
The power dissipated by the KAD5512P is primarily
dependent on the sample rate and the output modes:
LVDS vs. CMOS and DDR vs SDR. There is a static bias in
the analog supply, while the remaining power dissipation
is linearly related to the sample rate. The output supply
dissipation is approximately constant in LVDS mode, but
linearly related to the clock frequency in CMOS mode.
Nap/Sleep
Portions of the device may be shut down to save power
during times when operation of the ADC is not required.
Two power saving modes are available: Nap, and Sleep.
Nap mode reduces power dissipation to less than 95mW
and recovers to normal operation in approximately 1s.
Sleep mode reduces power dissipation to less than 6mW
but requires approximately 1ms to recover from a sleep
command.
Wake-up time from sleep mode is dependent on the state
of CSB; in a typical application CSB would be held high
during sleep, requiring a user to wait 150s max after
CSB is asserted (brought low) prior to writing ‘001x’ to
SPI Register 25. The device would be fully powered up, in
normal mode 1ms after this command is written.
Wake-up from Sleep Mode Sequence (CSB high)
Pull CSB Low
Wait 150s
Write ‘001x’ to Register 25
Wait 1ms until ADC fully powered on
SNR
20 log10
1
2
πf
INtJ
--------------------
=
(EQ. 1)
FIGURE 32. SNR vs CLOCK JITTER
tj = 100ps
tj = 10ps
tj = 1ps
tj = 0.1ps
10 BITS
12 BITS
14 BITS
50
55
60
65
70
75
80
85
90
95
100
1
10
100
1000
SNR
(dB
)
INPUT FREQUENCY (MHz)
TABLE 2. OUTMODE PIN SETTINGS
OUTMODE PIN
MODE
AVSS
LVCMOS
Float
LVDS, 3mA
AVDD
LVDS, 2mA
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B1N-MW-F3 | CONVERTER MOD DC/DC 18.5V 100W |
| MS27497P8F35PA | CONN RCPT 6POS WALL MNT W/PINS |
| IDT72V3640L7-5PFI | IC FIFO SS 1024X36 7-5NS 128TQFP |
| IDT72V3640L6PF | IC FIFO SS 1024X36 6NS 128-TQFP |
| MS3101R24-10S | CONN RCPT 7POS PANEL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KAD5512P-17Q72 | 功能描述:模數轉換器 - ADC 12-BIT 170MSPS SINGL ADC PROG LVDS/LVCMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| KAD5512P-21Q48 | 功能描述:模數轉換器 - ADC 12-BIT 210MSPS SINGL ADC PROG LVDS/LVCMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| KAD5512P-21Q72 | 功能描述:模數轉換器 - ADC 12-BIT 210MSPS SINGL ADC PROG LVDS/LVCMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| KAD5512P-25Q48 | 功能描述:模數轉換器 - ADC 12-BIT 250MSPS SINGL PROG LVDS/LVCMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| KAD5512P-25Q72 | 功能描述:模數轉換器 - ADC 12-BIT 250MSPS SINGL PROG LVDS/LVCMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。