- 您現在的位置：買賣IC網 > PDF目錄374300 > K9S2808V0B (SAMSUNG SEMICONDUCTOR CO. LTD.) TV 29C 29#16 PIN RECP PDF資料下載
參數資料
| 型號： | K9S2808V0B |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | TV 29C 29#16 PIN RECP |
| 中文描述： | SmartMedia卡 |
| 文件頁數： | 8/31頁 |
| 文件大小： | 481K |
| 代理商： | K9S2808V0B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
K9S2808V0C/B
8
SmartMedia
TM
K9S5608V0C/B
K9S6408V0C/B
PIN DESCRIPTION
Command Latch Enable(CLE)
The CLE input controls the path activation for commands sent to the command register. When active high, commands are latched
into the command register through the I/O ports on the rising edge of the WE signal.
Address Latch Enable(ALE)
The ALE input controls the activating path for address to the internal address registers. Addresses are latched on the rising edge of
WE with ALE high.
Chip Enable(CE)
The CE input is the device selection control. When CE goes high during a read operation the device is returned to standby mode.
However, when the device is in the busy state during program or erase, CE high is ignored and does not return the device to standby
mode.
Write Enable(WE)
The WE input controls writing to the I/O port. Commands, address and data are latched on the rising edge of the WE pulse.
Read Enable(RE)
The RE input is the serial data-out control, and when active drives the data onto the I/O bus.
I/O Port : I/O 0 ~ I/O 7
The I/O pins are used to input command, address and data, and to output data during read operations. The I/O pins float to high-z
when the chip is deselected or when the outputs are disabled.
Write Protect(WP)
The WP pin provides inadvertent write/erase protection during power transitions. The internal high voltage generator is reset when
the WP pin is active low.
Ready/Busy(R/B)
The R/B output indicates the status of the device operation. When low, it indicates that a program, erase or random read operation is
in process and returns to high state upon completion. It is an open drain output and does not float to high-z condition when the chip
is deselected or when outputs are disabled.
Low Voltage Detect(LVD)
The LVD is used to detect the proper supply voltage electrically. By connecting this pin to Vss through a pull-down resister, it is pos-
sible to distinguish 3.3V product from 5V product. When 3.3V is applied as Vcc to pins 12 and 22, a ’High’ level can be detected on
the system side if the device is a 3.3V product, and ’Low’ level for 5V product.
相關PDF資料 |
PDF描述 |
|---|---|
| K9S6408V0B | SmartMedia CARD |
| K9S6408V0C | SmartMedia CARD |
| K9S3208V0A | 4M x 8 bit SmartMedia Card |
| K9S3208V0A-SSB0 | 4M x 8 bit SmartMedia Card |
| K9T1G08U0M | 128M x 8 Bits NAND Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| K9S2808V0C | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SmartMedia CARD |
| K9S2808V0M | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:16M x 8 Bit SmartMedia Card |
| K9S2808V0M-SSB0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:16M x 8 Bit SmartMedia Card |
| K9S3208V0A | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:4M x 8 bit SmartMedia Card |
| K9S3208V0A-SSB0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:4M x 8 bit SmartMedia Card |
發布緊急采購，3分鐘左右您將得到回復。