- 您現在的位置：買賣IC網 > PDF目錄374264 > K4H1G0438M-UCB0 (SAMSUNG SEMICONDUCTOR CO. LTD.) 1Gb M-die DDR SDRAM Specification 66 TSOP-II with Pb-Free (RoHS compliant) PDF資料下載
參數資料
| 型號： | K4H1G0438M-UCB0 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 1Gb M-die DDR SDRAM Specification 66 TSOP-II with Pb-Free (RoHS compliant) |
| 中文描述： | 1Gb的的M -模與鉛DDR SDRAM的規格66 TSOP-II免費（符合RoHS） |
| 文件頁數： | 21/53頁 |
| 文件大?。?/td> | 669K |
| 代理商： | K4H1G0438M-UCB0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
- 21 -
REV. 1.0 November. 2. 2000
128Mb DDR SDRAM
3.3.2 Burst Write Operation
The Burst Write command is issued by having CS, CAS, and WE low while holding RAS high at the rising
edge of the clock(CK). The address inputs determine the starting column address. There is no write latency
relative to DQS required for burst write cycle. The first data of a burst write cycle must be applied on the DQ
pins tDS(Data-in setup time) prior to data strobe edge enabled after tDQSS from the rising edge of the
clock(CK) that the write command is issued. The remaining data inputs must be supplied on each subsequent
falling and rising edge of Data Strobe until the burst length is completed. When the burst has been finished, any
additional data supplied to the DQ pins will be ignored.
Figure 10. Burst write operation timing
1. The specific requirement is that DQS be valid(High or Low) on or before this CK edge. The case shown
(DQS going from High_Z to logic Low) applies when no writes were previously in progress on the bus.
If a previous write was in progress, DQS could be High at this time, depending on tDQSS.
*1
Command
< Burst Length=4 >
NOP
WRITEA
NOP
NOP
NOP
WRITEB
NOP
NOP
NOP
DQS
DQ
′
s
Din 3
Din 0 Din 1
Din 2
t
DQSSmax
2
0
1
5
3
4
8
6
7
t
WPRES*1
CK
CK
Din 3
Din 0
Din 1
Din 2
*1
相關PDF資料 |
PDF描述 |
|---|---|
| K4H1G0438M-UCB3 | 1Gb M-die DDR SDRAM Specification 66 TSOP-II with Pb-Free (RoHS compliant) |
| K4H1G0438M-ULA2 | 1Gb M-die DDR SDRAM Specification 66 TSOP-II with Pb-Free (RoHS compliant) |
| K4H1G0438M-ULB0 | 1Gb M-die DDR SDRAM Specification 66 TSOP-II with Pb-Free (RoHS compliant) |
| K4H1G0438M-ULB3 | 1Gb M-die DDR SDRAM Specification 66 TSOP-II with Pb-Free (RoHS compliant) |
| K4H1G0838D-TLA2 | 128Mb DDR SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| K4H1G0438M-UCB3 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:1Gb M-die DDR SDRAM Specification 66 TSOP-II with Pb-Free (RoHS compliant) |
| K4H1G0438M-ULA2 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:1Gb M-die DDR SDRAM Specification 66 TSOP-II with Pb-Free (RoHS compliant) |
| K4H1G0438M-ULB0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:1Gb M-die DDR SDRAM Specification 66 TSOP-II with Pb-Free (RoHS compliant) |
| K4H1G0438M-ULB3 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:1Gb M-die DDR SDRAM Specification 66 TSOP-II with Pb-Free (RoHS compliant) |
| K4H1G0638C | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:Stacked 1Gb C-die DDR SDRAM Specification |
發布緊急采購，3分鐘左右您將得到回復。