- 您現在的位置：買賣IC網 > PDF目錄384534 > ISPGAL22V10C-10LK (LATTICE SEMICONDUCTOR CORP) In-System Programmable E2CMOS PLD PDF資料下載
參數資料
| 型號： | ISPGAL22V10C-10LK |
| 廠商： | LATTICE SEMICONDUCTOR CORP |
| 元件分類： | PLD |
| 英文描述： | In-System Programmable E2CMOS PLD |
| 中文描述： | EE PLD, 10 ns, PDSO28 |
| 封裝： | 10.07 X 5.20 MM, SSOP-28 |
| 文件頁數： | 3/15頁 |
| 文件大?。?/td> | 247K |
| 代理商： | ISPGAL22V10C-10LK |
Specifications
ispGAL22V10
3
OUTPUT LOGIC MACROCELL (OLMC)
The ispGAL22V10 has a variable number of product terms per
OLMC. Of the ten available OLMCs, two OLMCs have access to
eight product terms (pins 17 and 27), two have ten product terms
(pins 18 and 26), two have twelve product terms (pins 19 and 25),
two have fourteen product terms (pins 20 and 24), and two
OLMCs have sixteen product terms (pins 21 and 23). In addition
to the product terms available for logic, each OLMC has an ad-
ditional product-term dedicated to output enable control.
OUTPUT LOGIC MACROCELL CONFIGURATIONS
ispGAL22V10 OUTPUT LOGIC MACROCELL (OLMC)
Each of the Macrocells of the ispGAL22V10 has two primary func-
tional modes: registered, and combinatorial I/O. The modes and
the output polarity are set by two bits (SO and S1), which are nor-
mally controlled by the logic compiler. Each of these two primary
modes, and the bit settings required to enable them, are described
below and on the following page.
REGISTERED
In registered mode the output pin associated with an individual
OLMC is driven by the Q output of that OLMC’s D-type flip-flop.
Logic polarity of the output signal at the pin may be selected by
specifying that the output buffer drive either true (active high) or
inverted (active low). Output tri-state control is available as an in-
dividual product-term for each OLMC, and can therefore be de-
fined by a logic equation. The D flip-flop’s /Q output is fed back
into the AND array, with both the true and complement of the
feedback available as inputs to the AND array.
NOTE: In registered mode, the feedback is from the /Q output of
the register, and not from the pin; therefore, a pin defined as
registered is an output only, and cannot be used for dynamic
I/O, as can the combinatorial pins.
COMBINATORIAL I/O
In combinatorial mode the pin associated with an individual OLMC
is driven by the output of the sum term gate. Logic polarity of the
output signal at the pin may be selected by specifying that the
output buffer drive either true (active high) or inverted (active low).
Output tri-state control is available as an individual product-term
for each output, and may be individually set by the compiler as
either “on” (dedicated output), “off” (dedicated input), or “product-
term driven” (dynamic I/O). Feedback into the AND array is from
the pin side of the output enable buffer. Both polarities (true and
inverted) of the pin are fed back into the AND array.
The output polarity of each OLMC can be individually programmed
to be true or inverting, in either combinatorial or registered mode.
This allows each output to be individually configured as either
active high or active low.
The ispGAL22V10 has a product term for Asynchronous Reset
(AR) and a product term for Synchronous Preset (SP). These two
product terms are common to all registered OLMCs. The Asyn-
chronous Reset sets all registers to zero any time this dedicated
product term is asserted. The Synchronous Preset sets all reg-
isters to a logic one on the rising edge of the next clock pulse after
this product term is asserted.
NOTE: The AR and SP product terms will force the Q output of
the flip-flop into the same state regardless of the polarity of the
output. Therefore, a reset operation, which sets the register output
to a zero, may result in either a high or low at the output pin,
depending on the pin polarity chosen.
A R
S P
D
Q
Q
C L K
4 T O 1
M U X
2 T O 1
M U X
相關PDF資料 |
PDF描述 |
|---|---|
| ISPGAL22V10B-10LJ | In-System Programmable E2CMOS PLD |
| ISPGAL22V10B-15LJ | 16-Wide LVDS Receiver w/Integrated Termination |
| ISPGAL22V10 | In-System Programmable E2CMOS PLD |
| ISPGAL22V10B-7LJ | In-System Programmable E2CMOS PLD |
| ISPGAL22V10C-15LJ | In-System Programmable E2CMOS PLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISPGAL22V10C-15LJ | 功能描述:SPLD - 簡單可編程邏輯器件 5V 22 I/O RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
| ISPGAL22V10C-15LJI | 功能描述:SPLD - 簡單可編程邏輯器件 PROGRAMMABLE LO VOLT E2CMOS PLD RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
| ISPGAL22V10C-15LJN | 功能描述:SPLD - 簡單可編程邏輯器件 PROGRAMMABLE LO VOLT E2CMOS PLD RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
| ISPGAL22V10C-15LK | 功能描述:SPLD - 簡單可編程邏輯器件 PROGRAMMABLE LO VOLT E2CMOS PLD RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
| ISPGAL22V10C-15LKI | 功能描述:SPLD - 簡單可編程邏輯器件 PROGRAMMABLE LO VOLT E2CMOS PLD RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
發布緊急采購，3分鐘左右您將得到回復。