- 您現在的位置：買賣IC網 > PDF目錄384534 > ISL97801ARZ-T (INTERSIL CORP) High Power LED Driver PDF資料下載
參數資料
| 型號： | ISL97801ARZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 顯示驅動器 |
| 英文描述： | High Power LED Driver |
| 中文描述： | LED DISPLAY DRIVER, PQCC20 |
| 封裝： | 4 X 4 MM, ROHS COMPLIANT, PLASTIC, QFN-20 |
| 文件頁數： | 13/19頁 |
| 文件大小： | 707K |
| 代理商： | ISL97801ARZ-T |
13
FN6428.1
April 2, 2007
Over Temperature Shutdown
An internal sense circuit disables PWM switching if the die
temperature exceeds +135°C. Switching is re-enabled when
the temperature falls below +100°C.
Internal 5V LDO
An internal LDO between VIN and VDC regulates VDC to
5V, to power control and gate drive circuits when VIN
exceeds 5.1V. In normal operation decouple VDC with at
least 3.3μF. In applications where the input supply is less
than 5.5V, VDC should be tied directly to VIN.
LED Temperature Control
LED lifetime reduces dramatically with elevated
temperature. An over temperature control circuit utilizing the
thermistor voltage at TEMP reduces the LED bias current
when VTEMP exceeds the threshold voltage on TMAX. To
minimize noise injection use a potential divider between
VDC and GND to set the voltage on TMAX, as shown in
Figure 34. The value of TMAX for a specific threshold
temperature is determined by the choice of thermistor
temperature coefficient. Disable the function by connecting
the TMAX pin to VDC and TEMP pin to GND
.
Component Selection
Input Capacitor
Switching regulators require input capacitors to deliver peak
charging current and to reduce the impedance of the input
supply. This reduces interaction between the regulator and
input supply, improving system stability. The high switching
frequency of the loop causes almost all ripple current to flow
in the input capacitor, which must be rated accordingly.
Considerably more input current ripple is generated in buck
mode than boost mode. In buck mode input current is
alternately switched between I
OUT
and zero. The rms
current flow in the input capacitor is given by:
Where: D = Duty Cycle
The input current is maximum for D = 0.5 and when I
OUT
approaches current limit (2.4A) giving a value of around
1.2A.
A capacitor with low internal series resistance should be
chosen to minimize heating effects and improve system
efficiency, such as X5R or X7R ceramic capacitors, which
offer small size and a lower value of temperature and voltage
coefficient compared to other ceramic caps.
In boost mode input current flows continuously into the
inductor, with an AC ripple component proportional to the
rate of inductor charging only and smaller value input
capacitors may be used. It is recommended that an input
capacitor of at least 10μF be used. Ensure the voltage rating
of the input capacitor is suitable to handle the full supply
range.
In automotive applications the input capacitor can be
protected from exposure to high voltages present during
fault conditions (load dump) by connecting it downstream of
the fault protection switch, as shown in Figures 39 and 40.
Inductor
Careful selection of inductor value will optimise circuit
operation. Inductor type and value influence many key
parameters, including ripple current, current limit, efficiency,
transient performance and stability. Internal slope
compensation has been optimised for inductor values
between 4.7μH and 10μH. Ensure the inductor current rating
is capable of handling the current limit value in the
configuration used (2.4A for buck, 3.5A for boost). If an
inductor core is chosen with too low a current rating,
saturation in the core will cause the effective inductor value
to fall, leading to an increase in peak to average current
level, poor efficiency and overheating in the core.
FIGURE 33. EXTERNAL OVP CIRCUIT
COUT
20μF
R1
100
VIN
FB
SWS1 SWS2
SWD1
SWD2
VBAT FAULT
ISL97801
VBAT
ZOVP
VOUT
L1
10μH
0.5
RSENSE
R
0
EL7801
GND
VIN
TEMP
Thermistor
Cose to
LEDs
VDC
LDO
CREG
0.47uF
RM1
20k
RT
10K
+
-
Temp
Compensation
RM2
80k
TMAX
FB Level Adjust
Current
FIGURE 34. OVER-TEMPERATURE CIRCUIT
I
CAPRMS
I
OUT
D
D
2
–
(
)
=
(EQ. 3)
ISL97801
相關PDF資料 |
PDF描述 |
|---|---|
| ISL97801ARZ-TK | High Power LED Driver |
| ISL9R1560P2 | 8A, 600V Stealth Diode(8A，600V Stealth二極管) |
| ISL9R860P2 | 8A, 600V Stealth Diode(8A，600V Stealth二極管) |
| ISO808 | Isolated 12-Bit Sampling Analog-To-Digital Converter(隔離的12位采樣A\D轉換器) |
| ISP321-1 | HIGH DENSITY MOUNTING PHOTOTRANSISTOR OPTICALLY COUPLED ISOLATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL97801ARZ-TK | 功能描述:IC LED DRIVER AUTOMOTIVE 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:60 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?線性（LDO），PWM，升壓（升壓） 輸出數:8 內部驅動器:是 類型 - 主要:背光 類型 - 次要:RGB，白色 LED 頻率:500kHz ~ 1.5MHz 電源電壓:4.75 V ~ 26 V 輸出電壓:45V 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* 工作溫度:-40°C ~ 85°C |
| ISL97801BOOSTEVALZ | 功能描述:EVAL BOARD FOR ISL97801 RoHS:是 類別:編程器，開發系統 >> 評估板 - LED 驅動器 系列:* 標準包裝:1 系列:PowerWise® 電流 - 輸出 / 通道:20mA 輸出及類型:1，非隔離 輸出電壓:17V 特點:可調光 輸入電壓:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相關產品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| ISL97900CRZ | 功能描述:LED照明驅動器 High Current RGB Driver/Controller, 28L 4x5 QFN, Commercial RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| ISL97900CRZ-T | 功能描述:LED照明驅動器 High Current RGB Driver/Controller, 28L 4x5 QFN, Commercial RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| ISL97900CRZ-T7A | 功能描述:LED照明驅動器 High Current RGB Driver/Controller, 28L 4x5 QFN,Commercial T RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。