- 您現在的位置：買賣IC網 > PDF目錄383182 > ISL95810 (Intersil Corporation) Single Digitally Controlled Potentiometer (XDCP) PDF資料下載
參數資料
| 型號： | ISL95810 |
| 廠商： | Intersil Corporation |
| 元件分類： | 數字電位計 |
| 英文描述： | Single Digitally Controlled Potentiometer (XDCP) |
| 中文描述： | 單數控電位（數字電位器） |
| 文件頁數： | 10/13頁 |
| 文件大?。?/td> | 1160K |
| 代理商： | ISL95810 |
10
FN8090.1
October 7, 2005
volatile bytes only places the device in its standby mode. A
STOP condition during a write operation to a non-volatile
byte, initiates an internal non-volatile write cycle. The device
enters its standby state when the internal non-volatile write
cycle is completed.
An ACK, Acknowledge, is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (See Figure 16).
The ISL95810 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL95810 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation.
A valid Identification Byte contains 0101000 as the seven
MSBs. The LSB in the Read/Write bit. Its value is “1” for a
Read operation, and “0” for a Write operation (See Table 2).
TABLE 2. IDENTIFICATION BYTE FORMAT
0
1
0
1
0
0
0
R/W
(MSB)
(LSB)
FIGURE 15. VALID DATA CHANGES, START, AND STOP CONDITIONS
FIGURE 16. ACKNOWLEDGE RESPONSE FROM RECEIVER
FIGURE 17. BYTE WRITE SEQUENCE
SDA
SCL
START
DATA
STABLE
DATA
CHANGE
STOP
DATA
STABLE
SDA OUTPUT FROM
TRANSMITTER
SDA OUTPUT FROM
RECEIVER
8
1
9
START
ACK
SCL FROM
MASTER
HIGH IMPEDANCE
HIGH IMPEDANCE
S
T
A
R
T
S
T
O
P
IDENTIFICATION
BYTE
ADDRESS
BYTE
DATA
BYTE
A
C
K
SIGNALS FROM
THE MASTER
SIGNALS FROM
THE ISL95810
A
C
K
0
0
0
1
1
A
C
K
WRITE
SIGNAL AT SDA
0 0 0 0
0
0
0
0 0 0
ISL95810
相關PDF資料 |
PDF描述 |
|---|---|
| ISL95810WIU8Z | Single Digitally Controlled Potentiometer (XDCP) |
| ISL95810WIU8Z-T | Single Digitally Controlled Potentiometer (XDCP) |
| ISL95810WIRT8Z | Single Digitally Controlled Potentiometer (XDCP) |
| ISL95810WIRT8Z-T | Single Digitally Controlled Potentiometer (XDCP) |
| ISL95810UIU8Z-T | Single Digitally Controlled Potentiometer (XDCP) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL95810UI8Z | 制造商:Intersil Corporation 功能描述: |
| ISL95810UIRT8 | 功能描述:IC XDCP SGL 256-TAP 50KOHM 8-DFN RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| ISL95810UIRT8Z | 功能描述:IC XDCP 256-TAP 50KOHM 8-TDFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| ISL95810UIRT8Z-T | 功能描述:IC XDCP 256-TAP 50KOHM 8-TDFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95810UIU8 | 功能描述:IC XDCP SGL 256-TAP 50KOHM 8MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。