- 您現在的位置：買賣IC網 > PDF目錄384532 > ISL9212AIRZ (INTERSIL CORP) Charging System Safety Circuit PDF資料下載
參數資料
| 型號： | ISL9212AIRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Charging System Safety Circuit |
| 中文描述： | SWITCHING REGULATOR, PDSO12 |
| 封裝： | 4 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229WGED-4, TDFN-12 |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 490K |
| 代理商： | ISL9212AIRZ |
10
FN6384.0
November 14, 2006
The over shoot caused by a hot insertion is not very
dependent on the decoupling capacitance value. Especially
when ceramic type capacitors are used for decoupling. In
theory, the over shoot can rise up to twice of the DC output
voltage of the AC adapter. The actual peak voltage is
dependent on the damping factor that is mainly determined
by the parasitic resistance (R in Figure 25).
In practice, the input decoupling capacitor is recommended
to use a 16V X5R dielectric ceramic capacitor with a value
between 0.1μF to 1μF.
The output of the ISL9212A and the input of the charging
circuit typically share one decoupling capacitor. The
selection of that capacitor is mainly determined by the
requirement of the charging circuit. When using the ISL6292
family chargers, a 1μF, 6.3V, X5R capacitor is
recommended.
Layout Recommendation
The ISL9212A uses a thermally enhanced DFN package.
The exposed pad under the package should be connected to
the ground plane electrically as well as thermally. A grid of
1.0mm to 1.2mm pitch thermal vias in two rows and 4 to 5
vias per row is recommended (refer to the ISL9200EVAL1
evaluation board layout). The vias should be about 0.3mm to
0.33mm in diameter. Use some copper on the component
layer if possible to further improve the thermal performance
but it is not mandatory.
Since the ISL9212A is a protection device, the layout should
also pay attention to the spacing between tracks. When the
distance between the edges of two tracks is less than
0.76mm, an FMEA (failure mechanism and effect analysis)
should be performed to ensure that a short between those
two tracks does not lead to the charger output exceeding the
“Lithium-Safe” region limits. Intersil will have the FMEA
document for the solution using the ISL9212A and the
ISL6292C chip set but the layout FMEA should be added as
part of the analysis.
ISL9212A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9212B | Charging System Safety Circuit |
| ISL9212BIRZ | Charging System Safety Circuit |
| ISL9212EVAL1 | Charging System Safety Circuit |
| ISL9212 | Charging System Safety Circuit |
| ISL9212IRZ | Charging System Safety Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9212AIRZ-T | 功能描述:IC CHARGING SYSTEM SAFETY 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9212B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Charging System Safety Circuit |
| ISL9212BIRZ | 功能描述:IC SAFETY SYSTEM CHARGER 12-TDFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9212BIRZ-T | 功能描述:IC SAFETY SYSTEM CHARGER 12-TDFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9212EVAL1 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Charging System Safety Circuit |
發布緊急采購，3分鐘左右您將得到回復。