- 您現在的位置：買賣IC網 > PDF目錄383182 > ISL90843WIU1027Z (INTERSIL CORP) Quad Digital Controlled Potentiometers (XDCP⑩) PDF資料下載
參數資料
| 型號： | ISL90843WIU1027Z |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Quad Digital Controlled Potentiometers (XDCP⑩) |
| 中文描述： | QUAD 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO10 |
| 封裝： | ROHS COMPLIANT, MO-187BA, MSOP-10 |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 755K |
| 代理商： | ISL90843WIU1027Z |
8
FN8095.2
March 29, 2006
bus as a transmitter and the receiving device as the receiver.
The device controlling the transfer is a master and the
device being controlled is the slave. The master always
initiates data transfers and provides the clock for both
transmit and receive operations. Therefore, the ISL90843
operates as a slave device in all applications.
All communication over the I
2
C interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line can change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (See
Figure 11). On power-up of the ISL90843 the SDA pin is in
the input mode.
All I
2
C interface operations must begin with a START
condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH. The ISL90843 continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition is met (See
Figure 11). A START condition is ignored during the power-
up of the device.
All I
2
C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while
SCL is HIGH (See Figure 11). A STOP condition at the end
of a read operation, or at the end of a write operation places
the device in its standby mode.
An ACK, Acknowledge, is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (See Figure 12).
The ISL90843 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL90843 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation
A valid Identification Byte contains 01010 as the five MSBs,
and the following two bits matching the logic values present
at pins A1 and A0. The LSB is in the Read/Write bit. Its value
is “1” for a Read operation, and “0” for a Write operation
(See Table 1).
TABLE 1. IDENTIFICATION BYTE FORMAT
Logic values at pins A1, and A0 respectively
0
1
0
1
0
A1
A0
R/W
(MSB)
(LSB)
FIGURE 11. VALID DATA CHANGES, START, AND STOP CONDITIONS
FIGURE 12. ACKNOWLEDGE RESPONSE FROM RECEIVER
SDA
SCL
START
DATA
STABLE
DATA
CHANGE
STOP
DATA
STABLE
SDA OUTPUT FROM
TRANSMITTER
SDA OUTPUT FROM
RECEIVER
8
1
9
START
ACK
SCL FROM
MASTER
HIGH IMPEDANCE
HIGH IMPEDANCE
ISL90843
相關PDF資料 |
PDF描述 |
|---|---|
| ISL90843 | Low Noise, Low Power, I2C Bus, 256 Taps(低噪聲, 低功率, I2C總線, 256抽頭數字電位器) |
| ISL9208 | Multi-Cell Li-ion Battery Pack OCP/Analog Front End(多節鋰離子電池組OCP/模擬前端) |
| ISL9214 | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL9214RZ | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL9214RZ-T | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL90843WIU1027Z-TK | 功能描述:IC XDCP 256-TAP 10OHM 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| ISL9103 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:500mA 2.4MHz Low IQ High Efficiency Synchronous Buck Converter |
| ISL9103A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:500mA 2.4MHz Low IQ High Efficiency Synchronous Buck Converter |
| ISL9103AIRUAZ-T | 功能描述:IC REG BUCK SYNC ADJ 0.5A 6UTDFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:50 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:5 V ~ 25 V 輸入電壓:2.3 V ~ 5.5 V PWM 型:電流模式 頻率 - 開關:600kHz，1.2MHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 包裝:管件 供應商設備封裝:8-MSOP |
| ISL9103AIRUBZ-T | 功能描述:IC REG BUCK SYNC 1.5V .5A 6UTDFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:50 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:5 V ~ 25 V 輸入電壓:2.3 V ~ 5.5 V PWM 型:電流模式 頻率 - 開關:600kHz，1.2MHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 包裝:管件 供應商設備封裝:8-MSOP |
發布緊急采購，3分鐘左右您將得到回復。