- 您現在的位置：買賣IC網 > PDF目錄383182 > ISL90810UIU8-TK (INTERSIL CORP) Low Noise/Low Power/I2C Bus/256 Taps PDF資料下載
參數資料
| 型號： | ISL90810UIU8-TK |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Low Noise/Low Power/I2C Bus/256 Taps |
| 中文描述： | 50K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO8 |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 1126K |
| 代理商： | ISL90810UIU8-TK |
9
FN8234.1
October 13, 2005
The ISL90810 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL90810 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation.
A valid Identification Byte contains 0101000 as the seven
MSBs. The LSB is the Read/Write bit. Its value is “1” for a
Read operation, and “0” for a Write operation (See Table 2)
The address byte is set to 00h and follows the identification
byte. Read and write operations always point to address
00h, indicating the WR for the device.
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL90810 respnds with an ACK. At this time the device
enters its standby state (See Figure 17).
Data Protection
A valid Identification Byte. Address Byte, and total number of
SCL pulses act as a protection for the registers. During a
Write sequence, the Data Byte is loaded into an internal shift
register as it is received. The Data Byte is transferred to the
Wiper Register (WR) at the falling edge of the SCL pulse
that loads the last bit (LSB) of the Data Byte.
Read Operation
A Read operation consists of a three byte instruction
followed by one Data Byte (See Figure 18). The master
initiates the operation issuing the following sequence: a
START, the identification byte with the R/W bit set to "0", an
Address Byte, a second START, and a second Identification
byte with the R/W bit set to "1". After each of the three bytes,
the ISL90810 responds with an ACK. The the ISL90810
transmits Data Bytes as long as the master responds with an
ACK during the SCL cycle following the eighth bit of each
byte. The master terminates the read operation (issuing a
ACK and a STOP condition) following the last bit of the Data
Byte (See Figure 18).
TABLE 1. IDENTIFICATION BYTE FORMAT
0
1
0
1
0
0
0
R/W
(MSB)
(LSB)
FIGURE 15. VALID DATA CHANGES, START, AND STOP CONDITIONS
FIGURE 16. ACKNOWLEDGE RESPONSE FROM RECEIVER
SDA
SCL
START
DATA
STABLE
DATA
CHANGE
STOP
DATA
STABLE
SDA OUTPUT FROM
TRANSMITTER
SDA OUTPUT FROM
RECEIVER
8
1
9
START
ACK
SCL FROM
MASTER
HIGH IMPEDANCE
HIGH IMPEDANCE
ISL90810
相關PDF資料 |
PDF描述 |
|---|---|
| ISL90810UIU8Z | Low Noise/Low Power/I2C Bus/256 Taps |
| ISL90810UIU8Z-TK | Low Noise/Low Power/I2C Bus/256 Taps |
| ISL90840UAV2027Z | Quad Digitally Controlled Potentiometers (XDCP) |
| ISL90840WAV2027Z | Quad Digitally Controlled Potentiometers (XDCP) |
| ISL90842UIV1427Z | Quad Digitally Controlled Variable Resistors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL90810UIU8Z | 功能描述:IC POT DGTL 50K OHM 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| ISL90810UIU8Z-TK | 功能描述:IC POT DGTL 50K OHM 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL90810WAU8Z | 功能描述:IC POT XDCP SGL LN LP 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| ISL90810WAU8Z-TK | 功能描述:IC POT XDCP SGL LN LP 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL90810WIU8 | 功能描述:IC XDCP 256-TAP 10KOHM 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。