- 您現在的位置：買賣IC網 > PDF目錄384529 > ISL9005AIRFZ-T (INTERSIL CORP) LDO with Low ISUPPLY, High PSRR PDF資料下載
參數資料
| 型號： | ISL9005AIRFZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | LDO with Low ISUPPLY, High PSRR |
| 中文描述： | 2.5 V FIXED POSITIVE LDO REGULATOR, 0.4 V DROPOUT, PDSO8 |
| 封裝： | 2 X 3 MM, ROHS COMPLIANT, PLASTIC, DFN-8 |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 246K |
| 代理商： | ISL9005AIRFZ-T |
8
FN6452.0
March 14, 2007
Block Diagram
Functional Description
The ISL9005A contains all circuitry required to implement a
high performance LDO. High performance is achieved
through a circuit that delivers fast transient response to
varying load conditions. In a quiescent condition, the
ISL9005A adjusts its biasing to achieve the lowest standby
current consumption.
The device also integrates current limit protection, smart
thermal shutdown protection, and soft-start. Smart thermal
shutdown protects the device against overheating.
Power Control
The ISL9005A has an enable pin, EN, to control power to the
LDO output. When EN is low, the device is in shutdown
mode. During this condition, all on-chip circuits are off, and
the device draws minimum current, typically less than 0.1μA.
When the enable pin is asserted, the device first monitors
the output of the UVLO detector to ensure that VIN voltage is
at least about 2.1V. Once verified, the device initiates a start-
up sequence. During the start-up sequence, trim settings are
first read and latched. Then, sequentially, the bandgap,
reference voltage and current generation circuitry power up.
Once the references are stable, a fast-start circuit powers up
the LDO.
During operation, whenever the VIN voltage drops below
about 1.84V, the ISL9005A immediately disables the LDO
output. When VIN rises back above 2.1V, the device re-
initiates its start-up sequence and LDO operation will
resume automatically.
Reference Generation
The reference generation circuitry includes a trimmed
bandgap, a trimmed voltage reference divider, a trimmed
current reference generator, and an RC noise filter.
The bandgap generates a zero temperature coefficient (TC)
voltage for the reference divider. The reference divider
provides the regulation reference and other voltage
references required for current generation and over-
temperature detection.
The current generator outputs references required for
adaptive biasing as well as references for LDO output
current limit and thermal shutdown determination.
LDO Regulation and Programmable Output Divider
The LDO Regulator is implemented with a high-gain
operational amplifier driving a PMOS pass transistor. The
design of the ISL9005A provides a regulator that has low
quiescent current, fast transient response, and overall
stability across all operating and load current conditions.
LDO stability is guaranteed for a 1μF to 10μF output
capacitor that has a tolerance better than 20% and ESR less
than 200m
Ω
, and the design is performance-optimized for a
1μF output capacitor. Unless limited by the application, use
of an output capacitor value above 4.7μF is not
recommended as LDO performance improvement is
minimal.
Soft-start circuitry integrated into each LDO limits the initial
ramp-up rate to about 30μs/V to minimize current surge. The
ISL9005A provides short-circuit protection by limiting the
output current to about 425mA.
The LDO uses an independently trimmed 1V reference as its
input. An internal resistor divider drops the LDO output
voltage down to 1V. This is compared to the 1V reference for
regulation. The resistor division ratio is programmed in the
factory.
Overheat Detection
The bandgap outputs a proportional-to-temperature current
that is indicative of the temperature of the silicon. This
current is compared with references to determine if the
device is in danger of damage due to overheating. When the
die temperature reaches about +140°C, if the LDO is
sourcing more than 50mA it shuts down until the die cools
sufficiently. Once the die temperature falls back below about
+110°C, the disabled LDO is re-enabled and soft-start
automatically takes place.
VO
GND
BANDGAP AND
TEMPERATURE
SENSOR
UVLO
VIN
SHORT CIRCUIT,
THERMAL PROTECTION,
SOFT-START
EN
CONTROL
LOGIC
1.0V
0.94V
0.9V
GND
VOLTAGE AND
REFERENCE
GENERATOR
ISL9005A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9005AIRJZ-T | LDO with Low ISUPPLY, High PSRR |
| ISL9005AIRKZ-T | LDO with Low ISUPPLY, High PSRR |
| ISL9005AIRLZ-T | LDO with Low ISUPPLY, High PSRR |
| ISL9005AIRMZ-T | LDO with Low ISUPPLY, High PSRR |
| ISL9005AIRNZ-T | LDO with Low ISUPPLY, High PSRR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9005AIRJZ-T | 功能描述:IC REG LDO 2.8V .3A 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，可調式 輸出電壓:1.25 V ~ 10 V 輸入電壓:2.9 V ~ 12 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:700mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:Digi-Reel® 其它名稱:NCV8535MNADJR2GOSDKR |
| ISL9005AIRKZ-T | 功能描述:IC REG LDO 2.85V .3A 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，可調式 輸出電壓:1.25 V ~ 10 V 輸入電壓:2.9 V ~ 12 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:700mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:Digi-Reel® 其它名稱:NCV8535MNADJR2GOSDKR |
| ISL9005AIRLZ-T | 功能描述:IC REG LDO 2.9V .3A 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，可調式 輸出電壓:1.25 V ~ 10 V 輸入電壓:2.9 V ~ 12 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:700mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:Digi-Reel® 其它名稱:NCV8535MNADJR2GOSDKR |
| ISL9005AIRMZ-T | 功能描述:IC REG LDO 3V .3A 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，可調式 輸出電壓:1.25 V ~ 10 V 輸入電壓:2.9 V ~ 12 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:700mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:Digi-Reel® 其它名稱:NCV8535MNADJR2GOSDKR |
| ISL9005AIRNZ-T | 功能描述:IC REG LDO 3.3V .3A 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，可調式 輸出電壓:1.25 V ~ 10 V 輸入電壓:2.9 V ~ 12 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:700mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:Digi-Reel® 其它名稱:NCV8535MNADJR2GOSDKR |
發布緊急采購，3分鐘左右您將得到回復。