- 您現在的位置：買賣IC網 > PDF目錄384528 > ISL8500IRZ (INTERSIL CORP) Switching Regulator Control (Voltage Mode type AC/DC) ; Vin (V) max.: 10 to 35; Icc (mA) max.: 15; Fmax (kHz) max.: 500; Topr [Tjopr] (°C): -30 to +85; Remarks: Primary control MOSFET drive; Package: DIP; Pin count: 16 PDF資料下載
參數資料
| 型號： | ISL8500IRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Switching Regulator Control (Voltage Mode type AC/DC) ; Vin (V) max.: 10 to 35; Icc (mA) max.: 15; Fmax (kHz) max.: 500; Topr [Tjopr] (°C): -30 to +85; Remarks: Primary control MOSFET drive; Package: DIP; Pin count: 16 |
| 中文描述： | SWITCHING REGULATOR, 550 kHz SWITCHING FREQ-MAX, PDSO12 |
| 封裝： | 4 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229VGED-4, DFN-12 |
| 文件頁數： | 10/15頁 |
| 文件大小： | 622K |
| 代理商： | ISL8500IRZ |
10
FN6611.0
December 10, 2007
Detailed Description
The ISL8500 combines a standard buck PWM controller with
an integrated switching MOSFET. The buck controller drives
an internal N-Channel MOSFET and requires an external
diode to deliver load current up to 2A. A Schottky diode is
recommended for improved efficiency and performance over
a standard diode. The standard buck regulator can operate
from either an unregulated DC source, such as a battery,
with a voltage ranging from +5.5V to +25V, or from a
regulated system rail of +5V. When operating from +5.5V or
greater, the controller is biased from an internal +5V LDO
voltage regulator. The converter output is regulated down to
0.6V from either input source. These features make the
ISL8500 ideally suited for FPGA and wireless chipset power
applications.
The PWM control loop uses a single output voltage loop with
input voltage feed forward, which simplifies feedback loop
compensation and rejects input voltage variation. External
feedback loop compensation allows flexibility in output filter
component selection. The regulator switches at a fixed 500kHz.
The buck regulator is equipped with a lossless current limit
scheme. The current limit in the buck regulator is achieved
by monitoring the drain-to-source voltage drop of the internal
switching power MOSFET. The current limit threshold is
internally set at 3.5A. The part also features undervoltage
protection by latching the switching MOSFET driver to the
OFF-state during an overcurrent, when the output voltage is
lower than 70% of the regulated output. This helps minimize
power dissipation during a short-circuit condition. Due to
only the switching power MOSFET integration, there is no
overvoltage protection feature for this part.
+5V Internal Bias Supply (VDD)
Voltage applied to the VIN pin with respect to GND is
regulated to +5V DC by an internal LDO regulator. The output
of the LDO, VDD, is the bias voltage used by all the internal
control and protection circuitry. The VDD pin requires a
ceramic capacitor connected to GND. The capacitor serves to
stabilize the LDO and to decouple load transients.
The input voltage range for the ISL8500 is specified as
+5.5V to +25V or +5V ±10%. In the case of an unregulated
supply case, the power supply is connected to VIN only.
Once enabled, the linear regulator will turn-on and rise to
+5V on VDD. In the +5V supply case, the VDD and VIN pins
must be tied together to bypass the LDO. The external
decoupling capacitor is still required in this mode.
Operation Initialization
The power-on reset circuitry and enable inputs prevent false
start-up of the PWM regulator output. Once all the input
criteria are met, the controller soft-starts the output voltage
to the programmed level.
Power-On Reset and Undervoltage Lockout
The PWM portion of the ISL8500 automatically initializes
upon receipt of input power. The power-on reset (POR)
function continually monitors the VDD voltage. While below
the POR thresholds, the controller inhibits switching off the
internal power MOSFET. Once exceeded, the controller
initializes the internal soft-start circuitry. If either input supply
drops below their falling POR threshold during soft-start or
operation, the buck regulator latches off.
Enable and Disable
All internal power devices are held in a high-impedance
state, which ensures they remain off while in shutdown
mode. Typically, the enable input for a specific output is
toggled high after the input supply to that regulator is active
and the internal LDO has exceeded it’s POR threshold.
The EN pin enables the buck controller portion of the
ISL8500. When the voltage on the EN pin exceeds the POR
rising threshold, the controller initiates the soft-start function
for the PWM regulator. If the voltage on the EN pin drops
below the POR falling threshold, the buck regulator shuts
down.
Pulling the EN pin low simultaneously put the output into
shutdown mode and supply current drops to 100μA typical.
Soft-Start
Once the input supply latch and enable threshold are met, the
soft-start function is initialized. The soft-start circuitry begins
sourcing 30μA, from an internal current source, which
charges the external soft-start capacitor. The voltage on SS
begins ramping linearly from ground until the voltage across
the soft-start capacitor reaches 3.0V. This linear ramp is
applied to the non-inverting input of the internal error amplifier
and overrides the nominal 0.6V reference. The output voltage
reaches its regulation value when the soft-start capacitor
voltage reaches 1.6V. Connect a capacitor from SS pin to
ground. This capacitor (along with an internal 30μA current
source) sets the soft-start interval of the converter, T
SS
.
C
SS
μ
F
Upon disable, the SS pin voltage will discharge to zero voltage.
Power Good
PG is an open-drain output of a window comparator that
continuously monitors the buck regulator output voltage. PG is
actively held low when EN is low and during the buck regulator
soft-start period. After the soft-start period terminates, PG
becomes high impedance as long as the output voltage is
within ±12% of the nominal regulation voltage set by FB. When
VOUT drops 12% below or rises 12% above the nominal
regulation voltage, the ISL8500 pulls PG low. Any fault
condition forces PG low until the fault condition is cleared by
attempts to soft-start. For logic level output voltages, connect
an external pull-up resistor between PG and VDD. A 100k
Ω
resistor works well in most applications.
[
]
50 T
SS
s
[ ]
=
(EQ. 1)
ISL8500
相關PDF資料 |
PDF描述 |
|---|---|
| ISL8502 | 2.5A Synchronous Buck Regulator with Integrated MOSFETs |
| ISL8502IRZ | 2.5A Synchronous Buck Regulator with Integrated MOSFETs |
| ISL8560MREP | DC/DC Power Switching Regulator |
| ISL8560 | DC/DC Power Switching Regulator |
| ISL8601 | Single-Phase, PMBus-Enabled PWM Controller with Integrated FET Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL8500IRZ-T | 功能描述:IC REG BUCK ADJ 2A 12DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:兩者兼有 輸出數:1 輸出電壓:5V，1 V ~ 10 V 輸入電壓:3.5 V ~ 28 V PWM 型:電流模式 頻率 - 開關:220kHz ~ 1MHz 電流 - 輸出:600mA 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:16-QSOP |
| ISL8501EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL8501 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL8501IRZ | 功能描述:電壓模式 PWM 控制器 INTEGRTD FETUCK 4X 4 24LD W/ANNEAL RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL8501IRZ-T | 功能描述:電壓模式 PWM 控制器 INTEGRTD FETUCK 4X 4 24LD W/ANNEAL RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL8502AEVAL1Z | 功能描述:EVAL BOARD FOR ISL8502 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。