- 您現在的位置：買賣IC網 > PDF目錄383165 > ISL8010IUZ (INTERSIL CORP) Monolithic 600mA Step-Down Regulator with Low Quiescent Current PDF資料下載
參數資料
| 型號： | ISL8010IUZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Monolithic 600mA Step-Down Regulator with Low Quiescent Current |
| 中文描述： | 1.2 A SWITCHING REGULATOR, 1600 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | ROHS COMPLIANT, MSOP-10 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 543K |
| 代理商： | ISL8010IUZ |
10
FN6191.0
September 27, 2005
Applications Information
Product Description
The ISL8010 is a synchronous, integrated FET 600mA step-
down regulator which operates from an input of 2.5V to 5.5V.
The output voltage is user-adjustable with a pair of external
resistors.
When the load is very light, the regulator automatically
operates in the PFM mode, thus achieving high efficiency at
light load (>70% for 1mA load). When the load increases,
the regulator automatically switches over to a voltage-mode
PWM operating at nominal 1.4MHz switching frequency. The
efficiency is up to 95%.
It can also operate in a fixed PWM mode or be synchronized
to an external clock up to 12MHz for improved EMI
performance.
PFM Operation
The heart of the ISL8010 regulator is the automatic
PFM/PWM controller.
If the SYNC pin is connected to ground, the regulator
operates automatically in either the PFM or PWM mode,
depending on load. When the SYNC pin is connected to V
IN
,
the regulator operates in the fixed PWM mode. When the pin
is connected to an external clock ranging from 1.6MHz to
12MHz, the regulator is in the fixed PWM mode and
synchronized to the external clock frequency.
In the automatic PFM/PWM operation, when the load is light,
the regulator operates in the PFM mode to achieve high
efficiency. The top P-channel MOSFET is turned on first. The
inductor current increases linearly to a preset value before it
is turned off. Then the bottom N-channel MOSFET turns on,
and the inductor current linearly decreases to zero current.
The N-channel MOSFET is then turned off, and an anti-
ringing MOSFET is turned on to clamp the LX pin to VO.
Both MOSFETs remain off until VFB drops below the internal
reference voltage of 0.8V. The inductor current looks like
triangular pulses. The frequency of the pulses is mainly a
function of output current. The higher the load, the higher the
frequency of the pulses until the inductor current becomes
continuous. At this point, the controller automatically
changes to PWM operation.
PWM Operation
The regulator operates the same way in the forced PWM or
synchronized PWM mode. In this mode, the inductor current
is always continuous and does not stay at zero.
In this mode, the P-channel MOSFET and N-channel
MOSFET always operate complementary. When the
P-channel MOSFET is on and the N-channel MOSFET off,
the inductor current increases linearly. The input energy is
transferred to the output and also stored in the inductor.
When the P-channel MOSFET is off and the N-channel
MOSFET on, the inductor current decreases linearly, and
energy is transferred from the inductor to the output. Hence,
the average current through the inductor is the output
current. Since the inductor and the output capacitor act as a
low pass filter, the duty cycle ratio is approximately equal to
V
O
divided by V
IN
.
The output LC filter has a second order effect. To maintain
the stability of the converter, the overall controller must be
compensated. This is done with the fixed internally
compensated error amplifier and the PWM compensator.
Because the compensations are fixed, the values of input
and output capacitors are 10μF to 22μF ceramic and
inductor is 1.5μH to 2.2μH.
Forced PWM Mode/SYNC Input
Pulling the SYNC pin HI (>2.5V) forces the converter into
PWM mode in the next switching cycle regardless of output
current. The duration of the transition varies depending on the
output current. Figures 22 and 23 (under two different loading
conditions) show the device goes from PFM to PWM mode.
Start-Up and Shutdown
When the EN pin is tied to V
IN
, and V
IN
reaches
approximately 2.4V, the regulator begins to switch. The
inductor current limit is gradually increased to ensure proper
soft-start operation.
When the EN pin is connected to a logic low, the ISL8010 is
in the shutdown mode. All the control circuitry and both
MOSFETs are off, and V
OUT
falls to zero. In this mode, the
total input current is less than 1μA.
When the EN reaches logic HI, the regulator repeats the
start-up procedure, including the soft-start function.
Current Limit and Short-Circuit Protection
The current limit is set at about 1.2A for the PMOS. When a
short-circuit occurs in the load, the preset current limit
restricts the amount of current available to the output, which
causes the output voltage to drop as load demand
increases. When the output voltage drops 30mV below the
reference voltage, the converter will shutdown for a period of
time, approximated by Equation 1, and then restart. If the
overcurrent condition still exists, it will repeat the shutdown-
wait-restart event. This is called a “hiccup” event. The
average power dissipation is reduced, thereby reducing the
likelihood of damage current and thermal conditions in the IC.
Thermal Shutdown
Once the junction reaches about 145°C, the regulator shuts
down. Both the P-channel and the N-channel MOSFETs turn
off. The output voltage will drop to zero. With the output
MOSFETs turned off, the regulator will cool down. Once the
junction temperature drops to about 130°C, the regulator will
perform a normal restart.
tHICCUP
----------------------------
216u
+
≈
(EQ. 1)
ISL8010
相關PDF資料 |
PDF描述 |
|---|---|
| ISL8010IUZ-T13 | Monolithic 600mA Step-Down Regulator with Low Quiescent Current |
| ISL8010IUZ-T7 | Monolithic 600mA Step-Down Regulator with Low Quiescent Current |
| ISL8010 | Monolithic 600mA Step-Down Regulator with Low Quiescent Current(低靜態電流，單片600mA降壓調節器) |
| ISL8102CRZ | Two-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL8102CRZ-T | Two-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL8010IUZ-T13 | 功能描述:IC REG BUCK SYNC ADJ 0.6A 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:50 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:5 V ~ 25 V 輸入電壓:2.3 V ~ 5.5 V PWM 型:電流模式 頻率 - 開關:600kHz，1.2MHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 包裝:管件 供應商設備封裝:8-MSOP |
| ISL8010IUZ-T7 | 功能描述:IC REG BUCK SYNC ADJ 0.6A 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:50 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:5 V ~ 25 V 輸入電壓:2.3 V ~ 5.5 V PWM 型:電流模式 頻率 - 開關:600kHz，1.2MHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 包裝:管件 供應商設備封裝:8-MSOP |
| ISL8011 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1.2A Integrated FETs, High Efficiency Synchronous Buck Regulator |
| ISL80111EVAL1Z | 制造商:Intersil Corporation 功能描述:ISL80111 EVAL BOARD - 10LD DFN - ROHS COMPLIANT - Bulk 制造商:Intersil Corporation 功能描述:BOARD EVAL FOR ISL80111 制造商:Intersil 功能描述:ISL80111 EVAL |
| ISL80111IRAJZ | 功能描述:IC REG LDO ADJ 1A 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品培訓模塊:MIC5365/66 Ultra-small LDO Regulators 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3V 輸入電壓:最高 5.5V 電壓 - 壓降（標準）:0.155V @ 150mA 穩壓器數量:1 電流 - 輸出:150mA 電流 - 限制（最?。?200mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:4-UDFN 裸露焊盤，4-TMLF? 供應商設備封裝:4-TMLF?（1x1） 包裝:Digi-Reel® 其它名稱:576-3192-6 |
發布緊急采購，3分鐘左右您將得到回復。