- 您現在的位置：買賣IC網 > PDF目錄383165 > ISL6845IRZ-T (INTERSIL CORP) Improved Industry Standard Single-Ended Current Mode PWM Controller PDF資料下載
參數資料
| 型號： | ISL6845IRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Improved Industry Standard Single-Ended Current Mode PWM Controller |
| 中文描述： | 1 A SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 2 X 3 MM, ROHS COMPLIANT, PLASTIC, DFN-8 |
| 文件頁數： | 7/9頁 |
| 文件大?。?/td> | 264K |
| 代理商： | ISL6845IRZ-T |
7
V
DD
-
V
DD
is the power connection for the device. The total
supply current will depend on the load applied to OUT. Total
I
DD
current is the sum of the operating current and the
average output current. Knowing the operating frequency, f,
and the MOSFET gate charge, Qg, the average output
current can be calculated from:
To optimize noise immunity, bypass V
DD
to GND with a
ceramic capacitor as close to the V
DD
and GND pins as
possible.
VREF -
The 5.00V reference voltage output. +1.0/-1.5%
tolerance over line, load and operating temperature. Bypass
to GND with a 0.1
μ
F to 3.3
μ
F capacitor to filter this output as
needed.
Functional Description
Features
The ISL6842, ISL6843, ISL6844, ISL6845 current mode
PWMs make an ideal choice for low-cost flyback and forward
topology applications. With its greatly improved performance
over industry standard parts, it is the obvious choice for new
designs or existing designs which require updating.
Oscillator
The ISL6842, ISL6843, ISL6844, ISL6845 controllers have a
sawtooth oscillator with a programmable frequency range to
2MHz, which can be programmed with a resistor from VREF
and a capacitor to GND on the RTCT pin. (Please refer to
Fig. 4
for the resistor and capacitance required for a given
frequency.)
Soft Start Operation
Soft start must be implemented externally. One method,
illustrated below, clamps the voltage on COMP.
Gate Drive
The ISL6842, ISL6843, ISL6844, ISL6845 are capable of
sourcing and sinking 1A peak current. To limit the peak
current through the IC, an optional external resistor may be
placed between the totem-pole output of the IC (OUT pin)
and the gate of the MOSFET. This small series resistor also
damps any oscillations caused by the resonant tank of the
parasitic inductances in the traces of the board and the
FET’s input capacitance.
Slope Compensation
For applications where the maximum duty cycle is less than
50%, slope compensation may be used to improve noise
immunity, particularly at lighter loads. The amount of slope
compensation required for noise immunity is determined
empirically, but is generally about 10% of the full scale
current feedback signal. For applications where the duty
cycle is greater than 50%, slope compensation is required to
prevent instability. The minimum amount of slope
compensation required corresponds to 1/2 the inductor
downslope. Adding excessive slope compensation,
however, results in a control loop that behaves more as a
voltage mode controller than as current mode controller.
Slope compensation may added to the CS signal in the
following manner.
Fault Conditions
A Fault condition occurs if VREF falls below 4.65V. When a
Fault is detected OUT is disabled. When VREF exceeds
4.80V, the Fault condition clears, and OUT is enabled.
Ground Plane Requirements
Careful layout is essential for satisfactory operation of the
device. A good ground plane must be employed. A unique
section of the ground plane must be designated for high di/dt
currents associated with the output stage. V
DD
should be
bypassed directly to GND with good high frequency
capacitors.
I
OUT
Qg
f
×
=
(EQ. 5)
FIGURE 5. SOFT START
VREF
COMP
GND
I
I
FIGURE 6. CURRENT SENSE DOWNSLOPE
TIME
C
DOWNSLOPE
CURRENT SENSE SIGNAL
FIGURE 7. SLOPE COMPENSATION
VREF
RTCT
CS
I
I
ISL6842, ISL6843, ISL6844, ISL6845
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6845IU | Octal Buffers/Drivers With 3-State Outputs 20-SO -40 to 85 |
| ISL6845IBZ | Improved Industry Standard Single-Ended Current Mode PWM Controller |
| ISL6845IUZ | Improved Industry Standard Single-Ended Current Mode PWM Controller |
| ISL72991RH | Radiation Hardened Negative Low Dropout Adjustable Voltage Regulator |
| ISL72991RHVF | Radiation Hardened Negative Low Dropout Adjustable Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6845IU | 功能描述:IC REG CTRLR BST FLYBK ISO 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| ISL6845IU-T | 功能描述:IC REG CTRLR BST FLYBK ISO 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| ISL6845IUZ | 功能描述:電流型 PWM 控制器 CUR MODE PWM 50% DUT CYCLE 8.4V UVLO 8LD RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6845IUZ-T | 功能描述:IC REG CTRLR BST FLYBK ISO 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6881CAZ-T | 制造商:Intersil Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。