- 您現在的位置：買賣IC網 > PDF目錄381960 > ISL6840IU (INTERSIL CORP) Improved Industry Standard Single-Ended Current Mode PWM Controller PDF資料下載
參數資料
| 型號： | ISL6840IU |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Improved Industry Standard Single-Ended Current Mode PWM Controller |
| 中文描述： | 1 A SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | PLASTIC, MO-187AA, MSOP-8 |
| 文件頁數： | 8/11頁 |
| 文件大小： | 307K |
| 代理商： | ISL6840IU |
8
FN9124.6
June 28, 2005
V
DD
-
V
DD
is the power connection for the device. The total
supply current will depend on the load applied to OUT. Total
I
DD
current is the sum of the operating current and the
average output current. Knowing the operating frequency, f,
and the MOSFET gate charge, Qg, the average output
current can be calculated from:
To optimize noise immunity, bypass V
DD
to GND with a
ceramic capacitor as close to the V
DD
and GND pins as
possible.
VREF -
The 5.00V reference voltage output. +1.0/-1.5%
tolerance over line, load and operating temperature. Bypass
to GND with a 0.1
μ
F to 3.3
μ
F capacitor to filter this output as
needed.
Functional Description
Features
The ISL684x current mode PWMs make an ideal choice for
low-cost flyback and forward topology applications. With its
greatly improved performance over industry standard parts,
it is the obvious choice for new designs or existing designs
which require updating.
Oscillator
The ISL684x controllers have a sawtooth oscillator with a
programmable frequency range to 2MHz, which can be
programmed with a resistor from VREF and a capacitor to
GND on the RTCT pin. (Please refer to
Fig. 4
for the resistor
and capacitance required for a given frequency.)
Soft-Start Operation
Soft-start must be implemented externally. One method,
illustrated below, clamps the voltage on COMP.
Gate Drive
The ISL684x are capable of sourcing and sinking 1A peak
current. To limit the peak current through the IC, an optional
external resistor may be placed between the totem-pole
output of the IC (OUT pin) and the gate of the MOSFET. This
small series resistor also damps any oscillations caused by
the resonant tank of the parasitic inductances in the traces of
the board and the FET’s input capacitance.
Slope Compensation
For applications where the maximum duty cycle is less than
50%, slope compensation may be used to improve noise
immunity, particularly at lighter loads. The amount of slope
compensation required for noise immunity is determined
empirically, but is generally about 10% of the full scale
current feedback signal. For applications where the duty
cycle is greater than 50%, slope compensation is required to
prevent instability. The minimum amount of slope
compensation required corresponds to 1/2 the inductor
downslope. Adding excessive slope compensation,
however, results in a control loop that behaves more as a
voltage mode controller than as current mode controller.
Slope compensation may added to the CS signal in the
following manner.
Fault Conditions
A Fault condition occurs if VREF falls below 4.65V. When a
Fault is detected OUT is disabled. When VREF exceeds
4.80V, the Fault condition clears, and OUT is enabled.
Ground Plane Requirements
Careful layout is essential for satisfactory operation of the
device. A good ground plane must be employed. A unique
section of the ground plane must be designated for high di/dt
currents associated with the output stage. V
DD
should be
bypassed directly to GND with good high frequency
capacitors.
I
OUT
Qg
f
×
=
(EQ. 5)
FIGURE 5. SOFT-START
VREF
COMP
GND
I
FIGURE 6. CURRENT SENSE DOWNSLOPE
TIME
C
DOWNSLOPE
CURRENT SENSE SIGNAL
FIGURE 7. SLOPE COMPENSATION
VREF
RTCT
CS
I
ISL6840, ISL6841, ISL6842, ISL6843, ISL6844, ISL6845
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6841IU | Octal Buffers/Drivers With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6842IU | Octal Buffers/Drivers With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6843IU | Octal Buffers/Drivers With 3-State Outputs 20-SSOP -40 to 85 |
| ISL6844IU | Octal Buffers/Drivers With 3-State Outputs 20-SOIC -40 to 85 |
| ISL6841IRZ-T | Improved Industry Standard Single-Ended Current Mode PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6840IU-T | 功能描述:IC REG CTRLR BST FLYBK ISO 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| ISL6840IUZ | 功能描述:電流型 PWM 控制器 CUR MODE PWM 100% DU TY CYCLE 7.0V UVLO RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6840IUZ-T | 功能描述:IC REG CTRLR BST FLYBK ISO 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:75 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.3 V ~ 13.5 V 降壓:是 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:0°C ~ 70°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:管件 產品目錄頁面:1051 (CN2011-ZH PDF) 其它名稱:296-2543-5 |
| ISL6841EVAL3Z | 功能描述:EVALUATION BOARD FOR ISL6841 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6841IB | 功能描述:電流型 PWM 控制器 Single-End Current RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。