參數資料
型號： ISL6741IV
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： Flexible Double Ended Voltage and Current Mode PWM Controllers
中文描述： 0.5 A SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO16
封裝： PLASTIC, MO-153-AB, TSSOP-16
文件頁數： 19/29頁
文件大小： 639K
代理商： ISL6741IV
19
To obtain the proper value for R
TD
, EQ. 3 is used. Since
there is a 10ns propagation delay in the oscillator circuit, it
must be included in the calculation. The value of R
TD
selected is 8.06k
.
A similar procedure is used to determine the value of R
TC
using EQ. 2. The value of R
TC
selected is the series
combination of 17.4k
and 1.27k
. See section
Over
Current Component Selection
for further explanation.
Output Filter Design
The output filter inductor and capacitor selection is simple
and straightforward. Under steady state operating conditions
the voltage across the inductor is very small due to the large
duty cycle. Voltage is applied across the inductor only during
the switch transition time, about 45ns in this application.
Ignoring the voltage drop across the SR FETs, the voltage
across the inductor during the ON time with V
IN
= 48V is
where
V
L
is the inductor voltage
V
S
is the voltage across the secondary winding
V
OUT
is the output voltage
If we allow a current ramp,
I, of 5% of the rated output
current, the minimum inductance required is
An inductor value of 1.4
μ
H, rated for 18A was selected.
With a maximum input voltage of 53V, the maximum output
voltage is about 13V. The closest higher voltage rated
capacitor is 16V. Under steady state operating conditions the
ripple current in the capacitor is small, so it would seem
appropriate to have a low ripple current rated capacitor.
However, a high rated ripple current capacitor was selected
based on the nature of the intended load, multiple buck
regulators. To minimize the output impedance of the filter, a
Sanyo OSCON 16SH150M capacitor in parallel with a 22
μ
F
ceramic capacitor were selected.
Over Current Component Selection
There are two circuit areas to consider when selecting the
components for over current protection, current limit and
short circuit shutdown. The current limit threshold is fixed at
0.6V while the short circuit threshold is set to a fraction of the
duty cycle the designer wishes to define as a short circuit.
The current level that corresponds to the over current
threshold must be chosen to allow for the dynamic behavior
of an open loop converter. In particular, the low inductor
ripple current under steady state operation increases
significantly as the duty cycle decreases.
Figures 8 and 9 show the behavior of the inductor ripple
under steady state and over current conditions. In this
example, the peak current limit is set at 11A. The peak
current limit causes the duty cycle to decrease resulting in a
reduction of the average current through the inductor. The
implication is that the converter can not supply the same
output current in current limit that it can supply under steady
state conditions. The peak current limit setpoint must take
this behavior into consideration. A 3.32
current sense
resistor was selected for the rectified secondary of current
transformer T2, corresponding to a peak current limit
setpoint of 16.5A.
The short circuit protection involves setting a voltage
between 0 and 2V on the SCSET pin. The applied voltage
divided by 2 is the percent of maximum duty cycle that
corresponds to a short circuit when the peak current limit is
active. A divider from RTC to ground provides an easy
method to achieve this. The divider between RTC and GND
V
L
V
S
V
OUT
–
V
-----------------------------------------------
N
P
1
D
–
(
)
250
≈
=
=
mV
(EQ. 22)
L
V
------------------------
T
≥
----------------------------
1.04
=
=
μ
H
(EQ. 23)
FIGURE 8. STEADY STATE SECONDARY WINDING
VOLTAGE AND INDUCTOR CURRENT
14
13
12
11
10
9
8
0.9950
0.9960
0.9970
0.9980
0.9990
1.000
TIME (ms)
V (L1:1)
I
(L1)
FIGURE 9. SECONDARY WINDING VOLTAGE AND
INDUCTOR CURRENT DURING CURRENT LIMIT
OPERATION
0.986
0.988
0.990
0.992
0.994
1.000
TIME (ms)
0.996
0.998
15
10
5
V (L1:1)
I
(L1)
ISL6740, ISL6741
相關PDF資料
PDF描述
ISL6740 Flexible Double Ended Voltage and Current Mode PWM Controllers
ISL6740IB Flexible Double Ended Voltage and Current Mode PWM Controllers
ISL6740IV Octal Buffers/Drivers With 3-State Outputs 20-SSOP -40 to 85
ISL6741 Flexible Double Ended Voltage and Current Mode PWM Controllers(靈活的雙端電壓和電流模式PWM控制器)
ISL6845IB Improved Industry Standard Single Ended Current Mode PWM Controller
相關代理商/技術參數
參數描述
ISL6741IV-T 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF)
ISL6741IVZ 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6741IVZ-T 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6742AAZA 功能描述:IC REG CTRLR PWM CM/VM 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:75 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.3 V ~ 13.5 V 降壓:是 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:0°C ~ 70°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:管件 產品目錄頁面:1051 (CN2011-ZH PDF) 其它名稱:296-2543-5
ISL6742AAZA-T 功能描述:IC REG CTRLR PWM CM/VM 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*