- 您現在的位置：買賣IC網 > PDF目錄383164 > ISL6723AABZ (INTERSIL CORP) Flexible Single Ended Current Mode PWM Controllers PDF資料下載
參數資料
| 型號： | ISL6723AABZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Flexible Single Ended Current Mode PWM Controllers |
| 中文描述： | 1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MS-012AC, SOIC-16 |
| 文件頁數： | 9/23頁 |
| 文件大小： | 428K |
| 代理商： | ISL6723AABZ |
9
FN9237.0
October 19, 2005
Pin Descriptions
SLOPE -
Means by which the ISENSE ramp slope may be
increased for improved noise immunity or improved control
loop stability for duty cycles greater than 50%. An internal
current source charges an external capacitor to GND during
each switching cycle. The resulting ramp is scaled and
added to the ISENSE signal.
SLEEP (ISL6722A) -
A logic level control input that disables
the IC and activates the low power standby mode. SLEEP is
active high.
SYNC (ISL6723A) -
A bidirectional synchronization signal
used to coordinate the switching frequency of multiple units.
Synchronization may be achieved by connecting the SYNC
signal of each unit together or by using an external master
clock signal. The oscillator timing capacitor, C
T
, is still
required, even if an external clock is used. The first unit to
assert this signal assumes control.
RTCT -
This is the oscillator timing control pin. The
operational frequency and maximum duty cycle are set by
connecting a resistor, R
T
, between V
REF
and this pin and a
timing capacitor, C
T
, from this pin to LGND. The oscillator
produces a sawtooth waveform with a programmable
frequency range of 100kHz to 1.0MHz. The charge time, T
C
,
the discharge time, T
D
, the switching frequency, Fsw, and
the maximum duty cycle, Dmax, can be calculated from the
following equations:
Figure 4 may be used as a guideline in selecting the
capacitor and resistor values required for a given frequency.
COMP -
COMP is the output of the error amplifier and the
input of the PWM comparator. The control loop frequency
compensation network is connected between the COMP and
FB pins.
The ISL6722A, ISL6723A feature a built-in full cycle soft-
start. Soft-start is implemented as a clamp on the maximum
COMP voltage.
FB -
Feedback voltage input connected to the inverting input
of the error amplifier. The non-inverting input of the error
amplifier is internally tied to a reference voltage.
OV -
Overvoltage monitor input pin. This signal is compared
to an internal 2.5V reference to detect an overvoltage
condition.
UV -
Undervoltage monitor input pin. This signal is
compared to an internal 1.45V reference to detect an
undervoltage condition.
ISENSE -
This is the input to the current sense comparators.
The IC has two current sensing comparators, a PWM
comparator for peak current mode control, and an
overcurrent protection comparator. The overcurrent
comparator threshold is adjustable through the ISET pin.
Exceeding the over-current threshold will start a delayed
shutdown sequence. Once an overcurrent condition is
detected, the soft-start charge current source is disabled and
a discharge current source is enabled. The soft-start
capacitor begins discharging, and if it discharges to less than
4.375V (sustained overcurrent threshold), a shutdown
condition occurs and the GATE output is forced low. At this
point a reduced discharge current takes over until the soft-
start voltage reaches 0.27V (Reset Threshold). The GATE
output remains low until the reset threshold is attained. At
this point a soft-start cycle begins.
If the overcurrent condition ceases, and then an additional
50μs period elapses before the shutdown threshold is
reached, no shutdown occurs and the soft-start voltage is
allowed to recharge.
LGND -
LGND is a small signal reference ground for all
analog functions on this device.
PGND -
This pin provides a dedicated ground for the output
gate driver. The LGND and PGND pins should be connected
externally using a short printed circuit board trace close to
the IC. This is imperative to prevent large, high frequency
switching currents from flowing through the ground
metallization inside the IC. (Decouple V
C
to PGND with a
low ESR 0.1μF or larger capacitor.)
GATE -
This is the device output. It is a high current power
driver capable of driving the gate of a power MOSFET with
peak currents of
1.0A
. This GATE output is actively held low
when V
CC
is below the UVLO threshold.
The output high voltage is clamped to ~ 13.5V. Voltages
exceeding this clamp value should not be applied to the
GATE pin. The output stage provides very low impedance to
overshoot and undershoot.
V
C
-
This pin is for separate collector supply to the output
gate drive. Separate V
C
and PGnd helps decouple the IC’s
analog circuitry from the high power gate drive noise.
(Decouple V
C
to PGND with a low ESR 0.1μF or larger
capacitor.)
V
CC
-
V
CC
is the power connection for the device. Although
quiescent current, I
CC
, is low, it is dependent on the
frequency of operation. To optimize noise immunity, bypass
T
C
0.655
RT
CT
≈
S
(EQ. 1)
T
D
RT
–
CT
LN0.001
RT
RT
3.6
1.9
–
–
≈
S
(EQ. 2)
Fsw
+
T
D
T
C
---------------------
=
Hz
(EQ. 3)
(EQ. 4)
Dmax
T
C
Fsw
=
ISL6722A, ISL6723A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6722AABZ | 1024 x 9 x 2 Asynchronous Bidirectional FIFO Memory 64-TQFP 0 to 70 |
| ISL6722AAVZ | Flexible Single Ended Current Mode PWM Controllers |
| ISL6722AAVZ-T | Flexible Single Ended Current Mode PWM Controllers |
| ISL6722AABZ-T | GT 17C 17#16 PIN PLUG |
| ISL6723AABZ-T | Circular Connector; MIL SPEC:MIL-C-5015; Body Material:Metal; Series:GT; No. of Contacts:8; Connector Shell Size:20; Connecting Termination:Solder; Circular Shell Style:Straight Plug; Body Style:Straight; Circular Contact Gender:Pin |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6723AABZ-T | 功能描述:IC REG CTRLR PWM CM 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6726AAZ | 功能描述:IC REG CTRLR ISO PWM CM 20-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:75 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.3 V ~ 13.5 V 降壓:是 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:0°C ~ 70°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:管件 產品目錄頁面:1051 (CN2011-ZH PDF) 其它名稱:296-2543-5 |
| ISL6726AAZ-T | 功能描述:IC REG CTRLR ISO PWM CM 20-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6726AAZ-T7A | 功能描述:IC REG CTRLR ISO PWM CM 20-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6726EVAL1Z | 制造商:Intersil Corporation 功能描述:ISL6726 EVALUATION BOARD 1 - 20 LD QSOP - ROHS COMPLIAN - Bulk 制造商:Intersil Corporation 功能描述:BOARD EVAL FOR ISL6726 制造商:Intersil Corporation 功能描述:ISL6726 EVALUATION BOARD 1 - 20 Ld QSOP - ROHS COMPLIAN |
發布緊急采購，3分鐘左右您將得到回復。