- 您現在的位置：買賣IC網 > PDF目錄383164 > ISL6722AABZ (INTERSIL CORP) 1024 x 9 x 2 Asynchronous Bidirectional FIFO Memory 64-TQFP 0 to 70 PDF資料下載
參數資料
| 型號： | ISL6722AABZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1024 x 9 x 2 Asynchronous Bidirectional FIFO Memory 64-TQFP 0 to 70 |
| 中文描述： | 1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MS-012AC, SOIC-16 |
| 文件頁數： | 17/23頁 |
| 文件大小： | 428K |
| 代理商： | ISL6722AABZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁
17
FN9237.0
October 19, 2005
For purposes of this discussion we will assume the following:
3.3V output: 100mV total output ripple and noise
ESR: 60mV
Capacitor
Q: 10mV
ESL: 30mV
1.8V output: 50mV total output ripple and noise
ESR: 30mV
Capacitor
Q: 5mV
ESL: 15mV
For the 3.3V output:
The change in voltage due to the change in charge of the
output capacitor,
Q, determines how much capacitance is
required on the output.
ESL adds to the ripple and noise voltage in proportion to the
rate of change of current into the capacitor (V = L
di/dt).
Capacitors having high capacitance usually do not have
sufficiently low ESL. High frequency capacitors such as
surface mount ceramic or film are connected in parallel with
the high capacitance capacitors to address the effects of
ESL. A combination of high frequency and high ripple
capability capacitors is used to achieve the desired overall
performance. The analysis of the 1.8V output is similar to
that of the 3.3V output and is omitted for brevity. Two
OSCON 4SEP560M (560μF) electrolytic capacitors and a
22μF X5R ceramic 1210 capacitor were selected for both the
3.3 and 1.8V outputs. The 4SEP560M electrolytic capacitors
are each rated at 4520mA ripple current and 13m
of ESR.
The ripple current rating of just one of these capacitors is
adequate, but two are needed to meet the minimum ESR
and capacitance values.
The bias output is of such low power and current that it
places negligible stress on its filter capacitor. A single 0.1μF
ceramic capacitor was selected.
Control Loop Design
The major components of the feedback control loop are a
programmable shunt regulator, an opto-coupler, and the
inverting amplifier of the ISL6722A. The opto-coupler is used
to transfer the error signal across the isolation barrier. The
opto-coupler offers a convenient means to cross the
isolation barrier, but it adds complexity to the feedback
control loop. It adds a pole at about 10kHz and a significant
amount of gain variation due the current transfer ratio (CTR).
The CTR of the opto-coupler varies with initial tolerance,
temperature, forward current, and age.
A block diagram of the feedback control loop follows in
Figure 10.
The loop compensation is placed around the Error Amplifier
(EA) on the secondary side of the converter. The primary
side amplifier located in the control IC is used as a unity gain
inverting amplifier and provides no loop compensation. A
Type 2 error amplifier configuration was selected as a
precaution in case operation in continuous mode should
occur at some operating point.
Development of a small signal model for current mode
control is rather complex. The method of preference [1] was
selected for its ability to accurately predict loop behavior. To
further simplify the analysis, the converter will be modeled as
a single output supply with all of the output capacitance
reflected to the 3.3V output. Once the “single” output system
is compensated, adjustments to the compensation will be
required based on actual loop measurements.
The first parameter to determine is the peak current
feedback loop gain. Since this application is low power, a
resistor in series with the source of the power switching
MOSFET is used for the current feedback signal. For higher
power applications, a resistor would dissipate too much
power and current transformer would be used instead.
ESR
–
Ispk
Iout
-----------------------------
≤
---------------–
7.3m
=
=
(EQ. 35)
C
---------------–
(
)
Tr
2
≥
-------------------–
(
)
2.33
6
–
×
10
0.010
960
μ
F
=
=
(EQ. 36)
L
--------------
di
≤
-----------------------------------10
9
–
10.73
0.56nH
=
=
(EQ. 37)
+
-
PWM
POWER
STAGE
Z
3
Z
4
Z
1
Z
2
REF
REF
+
-
ISOLATION
ERROR AMPLIFIER
PRIMARY SIDE AMPLIFIER
V
OUT
FIGURE 10.
REF
+
-
Vout
Verror
FIGURE 11. TYPE 2 ERROR AMPLIFIER
ISL6722A, ISL6723A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6722AAVZ | Flexible Single Ended Current Mode PWM Controllers |
| ISL6722AAVZ-T | Flexible Single Ended Current Mode PWM Controllers |
| ISL6722AABZ-T | GT 17C 17#16 PIN PLUG |
| ISL6723AABZ-T | Circular Connector; MIL SPEC:MIL-C-5015; Body Material:Metal; Series:GT; No. of Contacts:8; Connector Shell Size:20; Connecting Termination:Solder; Circular Shell Style:Straight Plug; Body Style:Straight; Circular Contact Gender:Pin |
| ISL6729IB | Low-Cost Single-Ended Current-Mode PWM for Microcontroller Based Power Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6722AABZ-T | 功能描述:IC REG CTRLR PWM CM 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6722AARZ | 功能描述:IC REG CTRLR BST FLYBK ISO 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6722AARZ-T | 功能描述:IC REG CTRLR BST FLYBK ISO 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6722AAVZ | 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6722AAVZ-T | 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。