參數資料
型號： ISL6721AVZ
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： Flexible Single Ended Current Mode PWM Controller
中文描述： 1 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
封裝： 4.40 MM, ROHS COMPLIANT, PLASTIC, MO-153AB, TSSOP-16
文件頁數： 13/20頁
文件大?。?/td> 481K
代理商： ISL6721AVZ
13
The RMS current for the primary winding is 0.72A, for the
3.3V output, 4.23A, for the 1.8V output, 1.69A, and for the
bias winding, 85mA.
To minimize the transformer leakage inductance, the primary
was split into two sections connected in parallel and
positioned such that the other windings were sandwiched
between them. The output windings were configured so that
the 1.8V winding is a tap off of the 3.3V winding. Tapping the
1.8V output requires that the shared portion of the
secondary conduct the combined current of both outputs.
The secondary wire gauge must be selected accordingly.
The determination of current carrying capacity of wire is a
compromise between performance, size, and cost. It is
affected by many design constraints such as operating
frequency (harmonic content of the waveform) and the
winding proximity/geometry. It generally ranges between 250
and 1000 circular mils per ampere. A circular mil is defined
as the area of a circle 0.001” (1 mil) in diameter. As the
frequency of operation increases, the AC resistance of the
wire increases due to skin and proximity effects. Using
heavier gauge wire may not alleviate the problem. Instead
multiple strands of wire in parallel must be used. In some
cases Litz wire is required.
The winding configuration selected is:
Primary #1: 40T, 2 #30 bifilar
Secondary: 5T, 0.003” (3 mil) copper foil tapped at 3T
Bias: 17T #32
Primary #2: 40T, 2 #30 bifilar
The internal spacing and insulation system was designed for
1500 VDC dielectric withstand rating between the primary
and secondary windings.
Power MOSFET Selection
Selection of the main switching MOSFET requires
consideration of the voltage and current stresses that will be
encountered in the application, the power dissipated by the
device, its size, and its cost.
The input voltage range of the converter is 36 - 75V DC. This
suggests a MOSFET with a voltage rating of 150V is
required due to the flyback voltage likely to be seen on the
primary of the isolation transformer.
The losses associated with MOSFET operation may be
divided into three categories: conduction, switching, and
gate drive.
The conduction losses are due to the MOSFET’s ON
resistance.
where Rdson is the ON resistance of the MOSFET and
Iprms is the RMS primary current. Determining the
conduction losses is complicated by the variation of Rdson
with temperature. As junction temperature increases, so
does Rdson, which increases losses and raises the junction
temperature more, and so on. It is possible for the device to
enter a thermal runaway situation without proper
heatsinking. As a general rule of thumb, doubling the 25
o
C
Rdson specification yields a reasonable value for estimating
the conduction losses at 125
o
C junction temperature.
The switching losses have two components, capacitive
switching losses and voltage/current overlap losses. The
capacitive losses occur during turn on of the device and may
be calculated as follows:
where Cfet is the equivalent output capacitance of the
MOSFET. Device output capacitance is specified on
datasheets as Coss and is non-linear with applied voltage.
To find the equivalent discrete capacitance, Cfet, a charge
model is used. Using a known current source, the time
required to charge the MOSFET drain to the desired
operating voltage is determined and the equivalent
capacitance may be calculated.
The other component of the switching loss is due to the
overlap of voltage and current during the switching transition.
A switching transition occurs when the MOSFET is in the
process of either turning on or off. Since the load is
inductive, there is no overlap of voltage and current during
the turn on transition, so only the turn off transition is of
significance. The power dissipation may be estimated as:
where Tol is the duration of the overlap period and x ranges
from about 3 - 6 in typical applications and depends on
where the waveforms intersect. This estimate may predict
higher dissipation than is realized because a portion of the
turn off drain current is attributable to the charging of the
device output capacitance (Coss) and is not dissipative
during this portion of the switching cycle.
Pcond
Rdson
Iprms
2
=
W
(EQ. 18)
Pswcap
1
2
--
Cfet
Vin
2
Fsw
=
W
(EQ. 19)
Cfet
-------------------
t
=
F
(EQ. 20)
Psw
1
x
--
Ippk
Vin
Tol
Fsw
≈
(EQ. 21)
V
D-S
Ippk
Tol
FIGURE 6.
ISL6721
相關PDF資料
PDF描述
ISL6721 Flexible Single Ended Current Mode PWM Controller(靈活的單端電流模式PWM控制器)
ISL6722A 1024 x 9 x 2 Asynchronous Bidirectional FIFO Memory 44-PLCC 0 to 70
ISL6723AABZ Flexible Single Ended Current Mode PWM Controllers
ISL6722AABZ 1024 x 9 x 2 Asynchronous Bidirectional FIFO Memory 64-TQFP 0 to 70
ISL6722AAVZ Flexible Single Ended Current Mode PWM Controllers
相關代理商/技術參數
參數描述
ISL6721AVZ-T 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6721EVAL1 功能描述:EVALUATION BOARD ISL6721 RoHS:否 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796
ISL6721EVAL3Z 功能描述:EVAL BOARD 3 FOR ISL6721 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
ISL6722AABZ 功能描述:IC REG CTRLR PWM CM 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6722AABZ-T 功能描述:IC REG CTRLR PWM CM 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*