- 您現在的位置：買賣IC網 > PDF目錄383160 > ISL6596CRZ-T (INTERSIL CORP) Synchronous Rectified MOSFET Driver PDF資料下載
參數資料
| 型號： | ISL6596CRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 功率晶體管 |
| 英文描述： | Synchronous Rectified MOSFET Driver |
| 中文描述： | HALF BRDG BASED MOSFET DRIVER, PDSO10 |
| 封裝： | 3 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-220, DFN-10 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 301K |
| 代理商： | ISL6596CRZ-T |
6
FN9240.0
November 2, 2005
Operation and Adaptive Shoot-Through Protection
Designed for high speed switching, the ISL6596 MOSFET
driver controls both high-side and low-side N-Channel FETs
from one externally provided PWM signal.
A rising transition on PWM initiates the turn-off of the lower
MOSFET (see Timing Diagram). After a short propagation
delay [t
PDLL
], the lower gate begins to fall. Typical fall times
[t
FL
] are provided in the
Electrical Specifications
. Adaptive
shoot-through circuitry monitors the LGATE voltage and turns
on the upper gate following a short delay time [t
PDHU
] after
the LGATE voltage drops below ~1V. The upper gate drive
then begins to rise [t
RU
] and the upper MOSFET turns on.
A falling transition on PWM indicates the turn-off of the upper
MOSFET and the turn-on of the lower MOSFET. A short
propagation delay [t
PDLU
] is encountered before the upper gate
begins to fall [t
FU
]. The adaptive shoot-through circuitry
monitors the UGATE-PHASE voltage and turns on the lower
MOSFET a short delay time, t
PDHL
, after the upper MOSFET’s
gate voltage drops below 1V. The lower gate then rises [t
RL
],
turning on the lower MOSFET. These methods prevent both the
lower and upper MOSFETs from conducting simultaneously
(shoot-through), while adapting the dead time to the gate
charge characteristics of the MOSFETs being used.
This driver is optimized for voltage regulators with large step
down ratio. The lower MOSFET is usually sized larger
compared to the upper MOSFET because the lower
MOSFET conducts for a longer time during a switching
period. The lower gate driver is therefore sized much larger
to meet this application requirement. The 0.4
on-resistance
and 4A sink current capability enable the lower gate driver to
absorb the current injected into the lower gate through the
drain-to-gate capacitor of the lower MOSFET and help
prevent shoot through caused by the self turn-on of the lower
MOSFET due to high dV/dt of the switching node.
PWM Input and Threshold Control
A unique feature of the ISL6596 is the programmable PWM
logic threshold set by the control pin (VCTRL) voltage. The
VCTRL pin should connect to the VCC of the controller, thus
the PWM logic threshold follows with the voltage level of the
controller. For 5V applications, this pin can tie to the driver
VCC and simplify the routing.
The ISL6596 also features the adaptable tri-state PWM input.
Once the PWM signal enters the shutdown window, either
MOSFET previously conducting is turned off. If the PWM signal
remains within the shutdown window for longer than the gate
turn-off propagation delay of the previously conducting
MOSFET, the output drivers are disabled and both MOSFET
gates are pulled and held low. The shutdown state is removed
when the PWM signal moves outside the shutdown window.
The PWM rising and falling thresholds outlined in the
Electrical
Specifications
determine when the lower and upper gates are
enabled. During normal operation in a typical application, the
PWM rise and fall times through the shutdown window should
not exceed either output’s turn-off propagation delay plus the
MOSFET gate discharge time to ~1V. Abnormally long PWM
signal transition times through the shutdown window will simply
introduce additional dead time between turn off and turn on of
the synchronous bridge’s MOSFETs. For optimal performance,
no more than 50pF parasitic capacitive load should be present
on the PWM line of ISL6596 (assuming an Intersil PWM
controller is used).
Bootstrap Considerations
This driver features an internal bootstrap diode. Simply
adding an external capacitor across the BOOT and PHASE
pins completes the bootstrap circuit.
The following equation helps select a proper bootstrap
capacitor size:
where Q
G1
is the amount of gate charge per upper MOSFET
at V
GS1
gate-source voltage and N
Q1
is the number of
control MOSFETs. The
V
BOOT_CAP
term is defined as the
allowable droop in the rail of the upper gate drive.
As an example, suppose two IRLR7821 FETs are chosen as
the upper MOSFETs. The gate charge, Q
G
, from the data
sheet is 10nC at 4.5V (V
GS
) gate-source voltage. Then the
Q
GATE
is calculated to be 22nC at VCC level. We will
assume a 200mV droop in drive voltage over the PWM
cycle. We find that a bootstrap capacitance of at least
0.110
μ
F is required.
The next larger standard value
capacitance is 0.22
μ
F. A good quality ceramic capacitor is
recommended.
C
BOOT_CAP
Q
BOOT_CAP
-------------------------------------
≥
Q
GATE
Q
-------------------------------
VCC
GS1
N
Q1
=
(EQ. 1)
20nC
V
BOOT_CAP
(V)
C
B
(
2.0
1.6
1.4
1.0
0.8
0.6
0.4
0.2
0.0
0.3
0.0
0.1
0.2
0.4
0.5
0.6
0.9
0.7
0.8
1.0
Q
GATE
= 100nC
5nC
1.2
1.8
FIGURE 2. BOOTSTRAP CAPACITANCE vs BOOT RIPPLE
VOLTAGE
ISL6596
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6596 | Dual Low-Noise Wide-Bandwidth Precision Amplifier 8-PDIP -40 to 85 |
| ISL6596IBZ-T | Synchronous Rectified MOSFET Driver |
| ISL6596IRZ-T | Synchronous Rectified MOSFET Driver |
| ISL6605IB | Circular Connector; Body Material:Aluminum; Series:PT06; Number of Contacts:55; Connector Shell Size:22; Connecting Termination:Solder; Circular Shell Style:Straight Plug; Circular Contact Gender:Pin; Insert Arrangement:22-55 |
| ISL6605CB-T | Synchronous Rectified MOSFET Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6596IBZ | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:高端 輸入類型:非反相 延遲時間:200ns 電流 - 峰:250mA 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:600V 電源電壓:12 V ~ 20 V 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-DIP 包裝:管件 其它名稱:*IR2127 |
| ISL6596IBZ-T | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:高端 輸入類型:非反相 延遲時間:200ns 電流 - 峰:250mA 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:600V 電源電壓:12 V ~ 20 V 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-DIP 包裝:管件 其它名稱:*IR2127 |
| ISL6596IRZ | 功能描述:IC MOSFET DRVR SYNC BUCK 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:高端 輸入類型:非反相 延遲時間:200ns 電流 - 峰:250mA 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:600V 電源電壓:12 V ~ 20 V 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-DIP 包裝:管件 其它名稱:*IR2127 |
| ISL6596IRZ-T | 功能描述:IC MOSFET DRVR SYNC BUCK 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:高端 輸入類型:非反相 延遲時間:200ns 電流 - 峰:250mA 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:600V 電源電壓:12 V ~ 20 V 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-DIP 包裝:管件 其它名稱:*IR2127 |
| ISL6597CRZ | 功能描述:IC MOSFET DRVR DUAL SYNC 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:高端 輸入類型:非反相 延遲時間:200ns 電流 - 峰:250mA 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:600V 電源電壓:12 V ~ 20 V 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-DIP 包裝:管件 其它名稱:*IR2127 |
發布緊急采購，3分鐘左右您將得到回復。