- 您現在的位置：買賣IC網 > PDF目錄383157 > ISL6563CR (INTERSIL CORP) Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers PDF資料下載
參數資料
| 型號： | ISL6563CR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
| 中文描述： | SWITCHING CONTROLLER, 255 kHz SWITCHING FREQ-MAX, PQCC24 |
| 封裝： | 4 X 4 MM, PLASTIC, MO-220-VGGD-2, QFN-24 |
| 文件頁數： | 9/19頁 |
| 文件大小： | 516K |
| 代理商： | ISL6563CR |
9
FN9126.6
April 13, 2005
Figure 11, part of the section entitled
Input Capacitor
Selection,
can be used to determine the input-capacitor
RMS current based on load current and duty cycle. The
figure is provided as an aid in determining the optimal input
capacitor solution.
PWM OPERATION
One switching cycle for the ISL6563 is defined as the time
between consecutive PWM pulse terminations (turn-off of
the upper MOSFET on a channel). Each cycle begins when
a switching clock signal commands the upper MOSFET to
go off. The other channel’s upper MOSFET conduction is
terminated 1/2 of a cycle later.
Once a channel’s upper MOSFET is turned off, the lower
MOSFET remains on for a minimum of 1/3 cycle. This forced
off time is required to assure an accurate current sample.
Following the 1/3-cycle forced off time, the controller enables
the upper MOSFET output. Once enabled, the upper
MOSFET output transitions high when the sawtooth signal
crosses the adjusted error-amplifier output signal, as
illustrated in the ISL6563’s block diagram. Just prior to the
upper drive turning the MOSFET on, the lower MOSFET
drive turns the freewheeling element off. The upper
MOSFET is kept on until the clock signals the beginning of
the next switching cycle and the PWM pulse is terminated.
CURRENT SENSING
ISL6563 senses current by sampling the voltage across the
lower MOSFET during its conduction interval. MOSFET
r
DS(ON)
sensing is a no-added-cost method to sense current
for load line regulation, channel current balance, module
current sharing, and overcurrent protection.
The PHASE pins are used as inputs for each channel.
Internal circuitry samples the lower MOSFETs’ r
DS(ON)
voltage, once each cycle, during their conduction periods
and time multiplexes the sampled voltages across the ISEN
resistor. The current that is thus developed through the ISEN
resistor is duplicated and fed back through the FB pin to
create droop, as well as used for channel current balancing.
CHANNEL-CURRENT BALANCE
Another benefit of multiphase operation is the thermal
advantage gained by distributing the dissipated heat over
multiple devices and greater area. By doing this, the
designer avoids the complexity of driving multiple parallel
MOSFETs and the expense of using expensive heat sinks
and exotic magnetic materials.
In order to fully realize the thermal advantage, it is important
that each channel in a multiphase converter be controlled to
deliver about the same current at any load level. Intersil
multiphase controllers ensure current balance by comparing
each channel’s current to the average current delivered by
all channels and making appropriate adjustments to each
channel’s pulse width based on the error. The error signal
modifies the pulse width to correct any unbalance and force
the error toward zero.
OVERCURRENT PROTECTION
The individual channel currents, as sensed via the PHASE
pins and scaled via the ISEN resistor, are continuously
monitored and compared with an internal 95
μ
A reference
current. If both channels’ currents exceed, at any time, the
reference current, the overcurrent comparator triggers an
overcurrent event. Similarly, an OC event is also triggered if
either channel’s current exceeds the 95
μ
A reference for 7
consecutive switching cycles.
As a result of an OC event, output drives on both channels
turn off both upper and lower MOSFETs. The system then
waits in this state for a period of 4096 switching clock cycles.
The wait period is followed by a soft-start attempt
.
If the soft-
start attempt is successful, operation continues as normal.
Should the soft-start attempt fail, the ISL6563 repeats the
2048-cycle wait period and follows with another soft-start
attempt. This hiccup mode of operation continues indefinitely
(as depicted in Figure 4) for as long as the controller is
enabled or until the overcurrent condition is removed.
OUTPUT VOLTAGE SETTING
The ISL6563 uses a digital to analog converter (DAC) to gen-
erate a reference voltage based on the logic signals at the
VID pins. The DAC decodes the 5 or 6-bit logic signals into
one of the discrete voltages shown in Tables 1 - 3. Each VID
pin is pulled up to an internal 1.2V voltage by weak current
sources (about 45
μ
A current, decreasing to 0 as the voltage
at the VID pins varies from 0 to the internal 1.2V pull-up volt-
age). External pull-up resistors or active-high output stages
can augment the pull-up current sources, up to a voltage of
5V.
.
The ISL6563 accommodates three different DAC ranges:
Intel VRM9.0, AMD Hammer, or Intel VRM10.0 - see
Functional Pin Description
for proper connections for DAC
range compatibility.
OUTPUT CURRENT
FIGURE 4. OVERCURRENT BEHAVIOR IN HICCUP MODE
OUTPUT VOLTAGE
ISL6563
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6563CRZ | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
| ISL6563IR | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
| ISL6563CR-T | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
| ISL6563EVAL1 | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
| ISL6563IRZ | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6563CR-T | 功能描述:IC CTRLR PWM MULTIPHASE 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6563CR-TK | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6563CRZ | 功能描述:電流型 PWM 控制器 P6 TWO PHS CONT INTEGRTD DRVRS DESKT RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6563CRZ-T | 功能描述:電流型 PWM 控制器 P6 TWO PHS CONT INTEGRTD DRVRS DESKT RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6563CRZ-TK | 功能描述:IC CTRLR PWM MULTIPHASE 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。