- 您現在的位置：買賣IC網 > PDF目錄384525 > ISL6540 (Intersil Corporation) Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability PDF資料下載
參數資料
| 型號： | ISL6540 |
| 廠商： | Intersil Corporation |
| 英文描述： | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
| 中文描述： | 單相降壓PWM控制器，帶有集成的高速MOSFET驅動器和預偏置負載能力 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 518K |
| 代理商： | ISL6540 |
11
FN9214.0
March 9, 2006
Functional Description
Initialization
The ISL6540 automatically initializes upon receipt of power
without requiring any special sequencing of the input
supplies. The Power-On Reset (POR) function continually
monitors the input supply voltages (PVCC,VFF, VCC) and
the voltage at the EN pin. Assuming the EN pin is pulled to
above ~0.49V, the POR function initiates soft-start operation
after all input supplies exceed their POR thresholds.
With all input supplies above their POR thresholds, driving
the EN pin above 0.49 V initiates a soft-start cycle. In
addition to normal TTL logic, the enable pin can be used as
a voltage monitor with programmable hysteresis through the
use of the internal 10
μ
A sink current and an external resistor
divider. This feature is especially designed for applications
that have input rails greater than a 3.3V and require a
specific input rail POR and Hysteresis levels for better
undervoltage protection. Consider for a 12V application
choosing R
UP
= 100k
and R
DOWN
= 5.76k
there by
setting the rising threshold (V
EN_RTH
) to 10V and the falling
threshold (V
EN_FTH
) to 9V, for 1V of hysteresis (V
EN_HYS
).
Care should be taken to prevent the voltage at the EN pin
from exceeding VCC when using the programmable UVLO
functionality.
Soft-start
The POR function activates the internal 38
μ
A OTA which
begins charging the external capacitor (C
SS
) on the SS pin to a
target voltage of VCC. The ISL6540’s soft-start logic continues
to charge the SS pin until the voltage on COMP exceeds the
bottom of the oscillator ramp, at which point, the driver outputs
are enabled, with the low side MOSFET first being held low for
200ns to provide for charging of the bootstrap capacitor. Once
the driver outputs are enabled, the OTA’s target voltage is then
changed to the margined (if margining is being used) reference
voltage (V
REF_MARG
), and the SS pin is ramped up or down
accordingly. This method reduces startup surge currents due to
a pre-charged output by inhibiting regulator switching until the
control loop enters its linear region. By ramping the positive
input of the error amplifier to VCC and then to V
REF_MARG
, it is
even possible to mitigate surge currents from outputs that are
pre-charged above the set output voltage. As the SS pin
connects directly to the non-inverting input of the Error
Amplifier, noise on this pin should be kept to a minimum
through careful routing and part placement.
To prevent noise
injection into the error amplifier the SS capacitor should be
located within 150mils of the SS and GND pins.
Soft-start is
declared done when the drivers have been enabled and the SS
pin is within ±3mV of V
REF_MARG
.
Power Good
The power good comparator references the voltage on the
soft-start pin to prevent accidental tripping during margining.
The trip points are shown on Figure 3. Additionally, power
good will not be asserted until after the completion of the soft-
start cycle. A 0.1
μ
F capacitor at the PG_DLY pin will add an
additional ~5ms delay to the assertion of power good.
PG_DLY does not delay the deassertion of power good.
VMON
Under and Overvoltage Protection
The Undervoltage (UV) and Overvoltage (OV) protection
circuitry compares the voltage on the VMON pin with the
VCC POR
VFF POR
PVCC POR
EN POR
SOFT-START
HIGH = ABOVE POR; LOW = BELOW POR
AND
FIGURE 1. SOFT-START INITIALIZATION LOGIC
V
REF
I
EN_HYS
=10
μ
A
R
UP
R
DOWN
VIN
R
UP
V
EN_HYS
-------------------------
=
R
DOWN
R
V
EN_REF
EN_FTH
---------------------------–
=
V
EN_FTH
V
EN_RTH
V
EN_HYS
–
=
Sys_Enable
FIGURE 2. ENABLE POR CIRCUIT
FIGURE 3. UNDERVOLTAGE-OVERVOLTAGE WINDOW
-15%
-9%
V
REF_MARG
+9%
+15%
UV
UV
OV
GOOD
GOOD
T
PG_DLY
C
PG_DLY
A
--------------
=
ISL6540
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6540_06 | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
| ISL6540CRZ | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
| ISL6540CRZA | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
| ISL6540IRZ | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
| ISL6540IRZA | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6540ACRZ | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:75 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.3 V ~ 13.5 V 降壓:是 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:0°C ~ 70°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:管件 產品目錄頁面:1051 (CN2011-ZH PDF) 其它名稱:296-2543-5 |
| ISL6540ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| ISL6540ACRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6540ACRZ-T W/GOLD BOND WIRE ONLY - Tape and Reel |
| ISL6540AIRZ | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6540AIRZA | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。