- 您現在的位置：買賣IC網 > PDF目錄383154 > ISL6532BCR (INTERSIL CORP) PWM Control Circuit 16-SSOP 0 to 70 PDF資料下載
參數資料
| 型號： | ISL6532BCR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | PWM Control Circuit 16-SSOP 0 to 70 |
| 中文描述： | SWITCHING CONTROLLER, 280 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | 6 X 6 MM, PLASTIC, MO-220VJJB, QFN-20 |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 362K |
| 代理商： | ISL6532BCR |
8
ACPI State Transitions
Cold Start (S5/S4 to S0 Transition)
At the onset of a mechanical start, the ISL6532B receives it’s
bias voltage from the 5V Standby bus (5VSBY). As soon as
the SLP_S3 and SLP_S5 signals have transitioned HIGH,
the ISL6532B starts an internal counter. Following a cold
start or any subsequent S5 state, state transitions are
ignored until the system enters S0/S1. None of the
regulators will begin the soft start procedure until the 5V
Standby bus has exceeded POR, the 12V bus has exceeded
POR and V
NCH
has exceeded the trip level.
Once all of these conditions are met, the PWM error
amplifier will first be reset by internally shorting the COMP
pin to the FB pin. This reset lasts for 2048 clock cycles which
is typically 8.2ms (one clock cycle = 1/f
OSC
). The digital soft
start sequence will then begin.
The PWM error amplifier reference input is clamped to a level
proportional to the soft-start voltage. As the soft-start voltage
slews up, the PWM comparator generates PHASE pulses of
increasing width that charge the output capacitor(s). The
internal V
TT
LDO will also soft start through the reference
that tracks the output of the PWM regulator. The soft start
lasts for 2048 clock cycles, which is typically 8.2ms. This
method provides a rapid and controlled output voltage rise.
Figure 1 shows the soft start sequence for a typical cold
start. Due to the soft start capacitance, C
SS
, on the
VREF_IN pin, the S5 to S0 transition profile of the V
TT
rail
will have a more rounded features at the start and end of the
soft start whereas the V
DDQ
profile has distinct starting and
ending points to the ramp up.
By directly monitoring 12VATX and the SLP_S3 and SLP_S5
signals, the ISL6532B can achieve PGOOD status
significantly faster than other devices that depend on the
Latched_Backfeed_Cut signal for timing.
Active to Sleep (S0 to S3 Transition)
When SLP_S3 goes LOW with SLP_S5 still HIGH, the
ISL6532B will disable the V
TT
linear regulator. The V
DDQ
standby regulator will be enabled and the V
DDQ
switching
regulator will be disabled. NCH is pulled low to disable the
backfeed blocking MOSFET. PGOOD will also transition
LOW. When V
TT
is disabled, the internal reference for the
V
TT
regulator is internally shorted to the V
TT
rail. This allows
the V
TT
rail to float. When floating, the voltage on the V
TT
rail will depend on the leakage characteristics of the memory
and MCH I/O pins. It is important to note that the V
TT
rail
may not bleed down to 0V.
The V
DDQ
rail will be supported in the S3 state through the
standby V
DDQ
LDO. When S3 transitions LOW, the Standby
regulator is immediately enabled. The switching regulator is
disabled synchronous to the switching waveform. The shut
off time will range between 4 and 8
μ
s. The standby LDO is
capable of supporting up to 650mA of load with P5VSBY tied
to the 5V Standby Rail. The standby LDO may receive input
from either the 3.3V Standby rail or the 5V Standby rail
through the P5VSBY pin. It is recommended that the 5V
Standby rail be used as the current delivery capability of the
LDO is greater.
Sleep to Active (S3 to S0 Transition)
When SLP_S3 transitions from LOW to HIGH with SLP_S5
held HIGH and after the 12V rail exceeds POR, the
ISL6532B will enable the V
DDQ
switching regulator, disable
the V
DDQ
standby regulator, enable the V
TT
LDO and force
the NCH pin to a high impedance state turning on the
blocking MOSFET. The internal short between the V
TT
reference and the V
TT
rail is released. Upon release of the
short, the capacitor on VREF_IN is then charged up through
the internal resistor divider network. The V
TT
output will
follow this capacitor charge-up, acting as the S3 to S0
transition soft start for the V
TT
rail. The PGOOD comparator
is enabled only after 2048 clock cycles, or typically 8.2ms,
have passed following the S3 transition to a HIGH state.
Figure 2 illustrates a typical state transition from S3 to S0. It
should be noted that the soft start profile of the V
TT
LDO
output will vary according to the value of the capacitor on the
VREF_IN pin.
Active to Shutdown (S0 to S4/S5 Transition)
When the system transitions from active, S0, state to
shutdown, S4/S5, state, the ISL6532B IC disables all
regulators and forces the PGOOD pin and the NCH pin
LOW.
FIGURE 1. TYPICAL COLD START
V
TT
V
DDQ
500mV/DIV
12VATX 2V/DIV
5VSBY
1V/DIV
S3
S5
500mV/DIV
PGOOD
5V/DIV
12V POR
SOFT START
INITIATES
SOFT START ENDS
PGOOD COMPARATOR
ENABLED
2048 CLOCK
CYCLES
2048 CLOCK
CYCLES
ISL6532B
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6532BCRZ | PWM Control Circuit 16-SOIC 0 to 70 |
| ISL6532CCRZ-T | R8C Series, 21 Group, WDTO 48P6Q-A |
| ISL6532C | PWM Control Circuit 16-SOIC 0 to 70 |
| ISL6532CCR | PWM Control Circuit 16-SOIC 0 to 70 |
| ISL6532CCR-T | PWM Control Circuit 16-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6532BCR-T | 功能描述:IC REG/CTRLR ACPI DUAL DDR 20QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6532BCRZ | 功能描述:電壓模式 PWM 控制器 DL DDRG W/3ALDO FOR SPRINGDALE MBS 20 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6532BCRZ-T | 功能描述:電壓模式 PWM 控制器 DL DDRG W/3ALDO FOR SPRINGDALE MBS 20 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6532CCR | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6532CCR-T | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。