- 您現在的位置：買賣IC網 > PDF目錄383153 > ISL6527IBZ (INTERSIL CORP) Single Synchronous Buck Pulse-Width Modulation (PWM) Controller PDF資料下載
參數資料
| 型號： | ISL6527IBZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| 中文描述： | SWITCHING CONTROLLER, 340 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MS-012AB, SOIC-14 |
| 文件頁數： | 5/14頁 |
| 文件大?。?/td> | 403K |
| 代理商： | ISL6527IBZ |
5
FN9056.7
April 8, 2005
Functional Pin Description
14 LEAD (SOIC)
TOP VIEW
16 LEAD 5X5 (QFN)
TOP VIEW
VCC
This pin provides the bias supply for the ISL6527. Connect a
well-decoupled 3.3V supply to this pin.
COMP and FB
COMP and FB are two of the three available external pins of
the error amplifier. The FB pin is the inverting input of the
internal error amplifier and the COMP pin is the error
amplifier output. These pins are used to compensate the
voltage-control feedback loop of the converter.
REF_IN
This pin is the third available external pin of the error
amplifier and represents the non-inverting input to the error
amplifier. Connect the desired reference voltage to this pin.
Voltage applied to this pin must not exceed 1.5V.
GND
This pin represents the signal and power ground for the IC.
Tie this pin to the ground island/plane through the lowest
impedance connection available.
PHASE
Connect this pin to the upper MOSFET’s source. This pin is
used to monitor the voltage drop across the upper MOSFET
for overcurrent protection.
UGATE
Connect this pin to the upper MOSFET’s gate. This pin
provides the PWM-controlled gate drive for the upper
MOSFET. This pin is also monitored by the adaptive shoot-
through protection circuitry to determine when the upper
MOSFET has turned off.
BOOT
This pin provides ground referenced bias voltage to the
upper MOSFET driver. A bootstrap circuit is used to create a
voltage suitable to drive a logic-level N-channel MOSFET.
LGATE
Connect this pin to the lower MOSFET’s gate. This pin
provides the PWM-controlled gate drive for the lower
MOSFET. This pin is also monitored by the adaptive shoot-
through protection circuitry to determine when the lower
MOSFET has turned off.
OCSET/SD
Connect a resistor (R
OCSET
) from this pin to the drain of the
upper MOSFET (V
IN
). R
OCSET
, an internal 20
μ
A current
source (I
OCSET
), and the upper MOSFET on-resistance
(r
DS(ON)
) set the converter overcurrent (OC) trip point
according to the following equation:
An overcurrent trip cycles the soft-start function.
Pulling OCSET/SD to a voltage level below 0.8V disables
the controller. Disabling the ISL6527 causes the oscillator to
stop, the LGATE and UGATE outputs to be held low, and the
soft-start circuitry to re-arm.
CT1 and CT2
These pins are the connections for the external charge
pump capacitor. A minimum of a 0.1
μ
F ceramic capacitor is
recommended for proper operation of the IC.
CPVOUT
This pin represents the output of the charge pump. The
voltage at this pin is the bias voltage for the IC. Connect a
decoupling capacitor from this pin to ground. The value of
the decoupling capacitor should be at least 10x the value of
the charge pump capacitor. This pin may be tied to the
bootstrap circuit as the source for creating the BOOT
voltage.
CPGND
This pin represents the signal and power ground for the
charge pump. Tie this pin to the ground island/plane through
the lowest impedance connection available.
12
14
13
4
3
2
1
LGATE
CPVOUT
UGATE
PHASE
VCC
BOOT
GND
CT1
11
7
6
5
9
8
10
CT2
OCSET/SD
FB
CPGND
REF_IN
COMP
1
3
4
15
CPVOUT
CT1
CT2
OCSET/SD
L
G
U
B
16
14
13
2
12
10
9
11
6
5
7
8
PHASE
VCC
CPGND
NC
N
F
C
R
I
PEAK
I
xR
r
DS ON
)
-------------------------------------------------
=
ISL6527
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6527IBZ-T | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6527AIB | Marine Lamp, 4 in x 6 in [101,6 mm x 152,4 mm], Spot Beam Pattern, 24 Vdc/60 W/2.5 A, Flush mounting |
| ISL6527AIBZ | Marine Lamp, 4 in x 6 in [101,6 mm x 152,4 mm], Spot Beam Pattern, 24 Vdc/60 W/2.5 A, Stud mounting |
| ISL6527AIBZ-T | Replacement Sealed Beams, 3.5 in x 5 in [76,2 mm x 127,0 mm], Trapezoid Beam Pattern, 12 Vdc/50 W/4 A |
| ISL6527CB-T | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6527IBZ-T | 功能描述:IC REG CTRLR BST PWM VM 14-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6527IR | 功能描述:IC REG CTRLR BST PWM VM 16-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6527IR-T | 功能描述:IC REG CTRLR BST PWM VM 16-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6527IRZ | 功能描述:IC REG CTRLR BST PWM VM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6527IRZ-T | 功能描述:IC REG CTRLR BST PWM VM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。