- 您現在的位置：買賣IC網 > PDF目錄384525 > ISL6525CB (INTERSIL CORP) Buck and Synchronous-Rectifier Pulse-Width Modulator (PWM) Controller PDF資料下載
參數資料
| 型號： | ISL6525CB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Buck and Synchronous-Rectifier Pulse-Width Modulator (PWM) Controller |
| 中文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封裝： | PLASTIC, MS-012-AB, SOIC-14 |
| 文件頁數： | 4/11頁 |
| 文件大?。?/td> | 120K |
| 代理商： | ISL6525CB |
4
Functional Pin Descriptions
RT (Pin 1)
This pin provides oscillator switching frequency adjustment.
By placing a resistor (R
T
) from this pin to GND, the nominal
200kHz switching frequency is increased according to the
following equation:
Conversely, connecting a pull-up resistor (R
T
) from this pin
to V
CC
reduces the switching frequency according to the
following equation.:
OCSET (Pin 2)
Connect a resistor (R
OCSET
) from this pin to the drain of the
upper MOSFET. R
OCSET
, an internal 200
μ
A current source
(I
OCS
), and the upper MOSFET on-resistance (r
DS(ON)
) set
the converter over-current (OC) trip point according to the
following equation:
I
DS ON
)
An over-current trip cycles the soft-start function.
SS (Pin 3)
Connect a capacitor from this pin to ground. This capacitor,
along with an internal 10
μ
A current source, sets the soft-
start interval of the converter.
COMP (Pin 4) and FB (Pin 5)
COMP and FB are the available external pins of the error
amplifier. The FB pin is the inverting input of the error
amplifier and the COMP pin is the error amplifier output.
These pins are used to compensate the voltage-control
feedback loop of the converter.
GND (Pin 6)
Signal ground for the IC. All voltage levels are measured with
respect to this pin.
PGOOD (Pin 7)
PGOOD is an open-drain output used to indicate the status
of the converter output voltage. This pin is pulled low when
the converter output is not within
±
10% of the set voltage. A
delay time can be programmed using the DELAY pin (pin
14). See Pin 14 description for more information.
PHASE (Pin 8)
Connect the PHASE pin to the upper MOSFET source. This
pin is used to monitor the voltage drop across the MOSFET
for over-current protection. This pin also provides the return
path for the upper gate drive.
UGATE (Pin 9)
Connect UGATE to the upper MOSFET gate. This pin
provides the gate drive for the upper MOSFET.
BOOT (Pin 10)
This pin provides bias voltage to the upper MOSFET driver.
A bootstrap circuit may be used to create a BOOT voltage
suitable to drive a standard N-Channel MOSFET.
PGND (Pin 11)
This is the power ground connection. Tie the lower MOSFET
source to this pin.
LGATE (Pin 12)
Connect LGATE to the lower MOSFET gate. This pin
provides the gate drive for the lower MOSFET.
VCC (Pin 13)
Provide a 12V bias supply for the chip to this pin.
DELAY (Pin 14)
This pin is used to program the delay of the PGOOD (pin 7)
signal by placing a capacitor between this pin and GND or
VCC. The external capacitor only delays the rising edge of
Typical Performance Curves
FIGURE 1. R
T
RESISTANCE vs FREQUENCY
FIGURE 2. BIAS SUPPLY CURRENT vs FREQUENCY
10
100
1000
SWITCHING FREQUENCY (kHz)
R
)
10
100
1000
R
T
PULLUP
TO +12V
R
T
PULLDOWN
TO V
SS
100
200
300
400
500
600
700
800
900
1000
80
70
60
50
40
30
20
10
0
I
V
SWITCHING FREQUENCY (kHz)
C
GATE
= 1000pF
C
GATE
= 3300pF
C
GATE
= 10pF
Fs
200kHz
T
6
)
--------------------
+
≈
(R
T
to GND)
Fs
200kHz
T
7
)
--------------------
–
≈
(R
T
to 12V)
I
PEAK
R
-------------------------------------------
=
ISL6525
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6526ACRZ | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6526AIBZ | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6526CRZ | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6529A | Dual Regulator.Synchronous Rectified Buck PWM and Linear Power Controller |
| ISL6535 | Synchronous Buck Pulse-Width Modulator (PWM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6525CB-T | 功能描述:IC REG CTRLR BUCK PWM VM 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6525CBZ | 功能描述:電壓模式 PWM 控制器 VTT REG FORVRM 8.5 1 4LD RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6525CBZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 14-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6526ACB | 功能描述:IC REG CTRLR BUCK PWM VM 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6526ACB-T | 功能描述:IC REG CTRLR BUCK PWM VM 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。