- 您現在的位置：買賣IC網 > PDF目錄383145 > ISL6308 (Intersil Corporation) Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6308 |
| 廠商： | Intersil Corporation |
| 英文描述： | Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85 |
| 中文描述： | 三相降壓PWM控制器，帶有高電流集成MOSFET驅動器 |
| 文件頁數： | 9/27頁 |
| 文件大小： | 765K |
| 代理商： | ISL6308 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
9
FN9208.2
October 19, 2005
LGATE1, LGATE2, and LGATE3 (Pins 34, 23, 17)
These pins are used to control the lower MOSFETs and are
monitored for shoot-through prevention purposes. Connect
these pins to the lower MOSFETs’ gates. Do not use
external series gate resistors as this might lead to shoot-
through.
PGOOD (Pin 35)
PGOOD is used as an indication of the end of soft-start. It is
an open-drain logic output that is low impedance until the
soft-start is completed and VOUT is equal to the VID setting.
Once in normal operation PGOOD indicates whether the
output voltage is within specified overvoltage and
undervoltage limits. If the output voltage exceeds these limits
or a reset event occurs (such as an overcurrent event),
PGOOD becomes high impedance again. The potential at
this pin should not exceed that of the potential at VCC pin by
more than a typical forward diode drop at any time.
OVP (Pin 38)
Overvoltage protection pin. This pin pulls to VCC when an
overvoltage condition is detected. Connect this pin to the
gate of an SCR or MOSFET tied across V
IN
and ground to
prevent damage to a load device.
Operation
Multi-Phase Power Conversion
Modern low voltage DC/DC converter load current profiles
have changed to the point that the advantages of multi-
phase power conversion are impossible to ignore. The
technical challenges associated with producing a single-
phase converter that is both cost-effective and thermally
viable have forced a change to the cost-saving approach of
multi-phase. The ISL6308 controller helps simplify
implementation by integrating vital functions and requiring
minimal output components. The block diagram on page 3
provides a top level view of multi-phase power conversion
using the ISL6308 controller.
Interleaving
The switching of each channel in a multi-phase converter is
timed to be symmetrically out of phase with each of the other
channels. In a 3-phase converter, each channel switches 1/3
cycle after the previous channel and 1/3 cycle before the
following channel. As a result, the three-phase converter has
a combined ripple frequency three times greater than the
ripple frequency of any one phase. In addition, the peak-to-
peak amplitude of the combined inductor currents is reduced
in proportion to the number of phases (Equations 1 and 2).
Increased ripple frequency and lower ripple amplitude mean
that the designer can use less per-channel inductance and
lower total output capacitance for any performance
specification.
Figure 1 illustrates the multiplicative effect on output ripple
frequency. The three channel currents (I
L1
, I
L2
, and I
L3
)
combine to form the AC ripple current and the DC load
current. The ripple component has three times the ripple
frequency of each individual channel current. Each PWM
pulse is terminated 1/3 of a cycle after the PWM pulse of the
previous phase. The peak-to-peak current for each phase is
about 7A, and the dc components of the inductor currents
combine to feed the load.
To understand the reduction of ripple current amplitude in the
multi-phase circuit, examine the equation representing an
individual channel peak-to-peak inductor current.
(
)
V
SW
V
IN
In Equation 1, V
IN
and V
OUT
are the input and output
voltages respectively, L is the single-channel inductor value,
and F
SW
is the switching frequency.
The output capacitors conduct the ripple component of the
inductor current. In the case of multi-phase converters, the
capacitor current is the sum of the ripple currents from each
of the individual channels. Compare Equation 1 to the
expression for the peak-to-peak current after the summation
of N symmetrically phase-shifted inductor currents in
Equation 2. Peak-to-peak ripple current decreases by an
amount proportional to the number of channels. Output
voltage ripple is a function of capacitance, capacitor
equivalent series resistance (ESR), and inductor ripple
current. Reducing the inductor ripple current allows the
designer to use fewer or less costly output capacitors.
Another benefit of interleaving is to reduce input ripple
current. Input capacitance is determined in part by the
maximum input ripple current. Multi-phase topologies can
improve overall system cost and size by lowering input ripple
current and allowing the designer to reduce the cost of input
capacitance. The example in Figure 2 illustrates input
FIGURE 1. PWM AND INDUCTOR-CURRENT WAVEFORMS
FOR 3-PHASE CONVERTER
PWM2, 5V/DIV
PWM1, 5V/DIV
I
L2
, 7A/DIV
I
L1
, 7A/DIV
I
L1
+ I
L2
+ I
L3
, 7A/DIV
I
L3
, 7A/DIV
PWM3, 5V/DIV
I
PP
V
----------L F
V
OUT
–
=
(EQ. 1)
I
C PP
,
V
----------------L F
N
V
–
(
)
V
IN
SW
=
(EQ. 2)
ISL6308
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6308CRZ | Three-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL6308CRZ-T | Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85 |
| ISL6308IRZ-T | Three-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL6315 | Two-Phase Multiphase Buck PWM Controller with Integrated MOSFET Drivers(帶集成MOSFET驅動器的雙相降壓PWM控制器) |
| ISL6316 | Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6308ACRZ | 功能描述:IC CTRLR PWM BUCK 3PHASE 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6308ACRZR5609 | 制造商:Intersil Corporation 功能描述:PB-FREE DAC-LESS MULTI-PHASE PWM CONTR W/3-DRIVERS, HARD WI - Rail/Tube |
| ISL6308ACRZ-T | 功能描述:IC CTRLR PWM BUCK 3PHASE 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6308ACRZ-TR5609 | 制造商:Intersil Corporation 功能描述:PB-FREE DAC-LESS MULTI-PHASE PWM CONTR W/3-DRIVERS, HARD WIR - Tape and Reel |
| ISL6308AEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL6308A RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。