- 您現在的位置：買賣IC網 > PDF目錄383144 > ISL6295CV-T (INTERSIL CORP) Low Voltage Fuel Gauge PDF資料下載
參數資料
| 型號： | ISL6295CV-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Low Voltage Fuel Gauge |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | PLASTIC, MO-153-AC, TSSOP-8 |
| 文件頁數： | 17/25頁 |
| 文件大?。?/td> | 387K |
| 代理商： | ISL6295CV-T |
17
FN9074.0
October 25, 2005
GPADA - GPAD ACCUMULATOR
GPADA is a 32 bit register that holds the total accumulated
value measured on the GPAD/IO1 pin. GPADA is
incremented by the value in GPADres every 0.5s as long as
the function is enabled by the AccV bit in the AccumCtrl
register.
The GAPDA register will rollover if it is allowed to count
beyond 0xFFFFFFFF, so proper register maintenance by the
host system is necessary. The GAPDA register may be
cleared by setting the “CLR6” bit in the ACCclr register.
GPADT - GPAD TIME COUNT REGISTER
GPADT records elapsed time for which measurements are
taken on the GPAD pin. GPADT is incremented at a rate of
2Hz for as long as GPAD accumulation is enabled.
Time accumulation in the GPADT register is not expected to
rollover over the life of the battery pack. If desired, the
GPADT register may be cleared by setting the “CLR7” bit in
the ACCclr register.
A/D CONFIGURATION REGISTER – ADconfig
(Address - 43 Hex/67 Decimal)
7
6
5
4
3
2
1
0
ADEN
Samp
Reserved
SampDiv (2:0)
ADEN
Master A/D enable: When set to a ‘1’, A/D
conversions can be performed. All A/D
conversions are disabled when it is cleared to ‘0’.
Samp
Sample Mode enable: This bit controls the
enabling of Sample mode when the ISL6295 is
not in a Power-on Reset, Sample-Sleep, or
Shelf-Sleep mode. When set to ‘1’, Sample
Mode is enabled and conversions will be
performed at a periodic rate determined by the
programming of the “SampDiv” bits. When
cleared, Sample Mode is disabled and the
ISL6295 will operate in Run Mode.
Reserved
Reserved bit.
SampDiv
The SampDiv bits define the time interval
between executing an A/D conversion cycle
sequence during Sample mode. The time
interval between each conversion cycle is
defined by: 2^(SampDiv) * 0.5s
Note that if the time taken to complete an A/D
conversion cycle is more than the defined
interval, the time-overlapped pending
conversion cycle(s) will be skipped until the
previous conversion cycle is complete. For
example, if SampDiv = 2, but the time taken to
complete a conversion cycle is 5s, then the
effective conversion time interval will be 6s.
ACCUMULATOR CONTROL REGISTER – AccCtrl
(Address - 63 Hex/99 Decimal)
7
6
5
4
3
2
1
0
Accum
Accl
AccT
AccV
tsel
Reserved
Accum
Accumulator Master Enable: Master enable
control for all accumulators. If any combination
of “Accl”, “AccT” and “AccV” are enabled,
“Accum” must also be enabled to permit
accumulation. If “Accum” is ‘0’, no accumulation
will occur regardless of the settings of “Accl”,
“AccT” and “AccV”.
Accl
Current Accumulation enable: When set to ‘1’,
current accumulation is enabled. The DCA and
CCA registers will periodically add the value of
the Ires register to its accumulated result. Also,
the DTC and CTC elapsed time counters will
count during discharge and charge respectively.
When “AccI” is cleared to ‘0’, current
accumulation is disabled.
AccT
Temperature Accumulation enable: When set to
‘1’, accumulation will be enabled in the TA. TA
will accumulate results from either ITres or
ETres register, depending on the setting of the
“tsel” bit. While enabled, the TAT eapsed time
counter will increment. When “AccT” is cleared
to ‘0’, TA accumulation will be disabled.
AccV
GPAD Voltage Accumulation enable: When set
to ‘1’, accumulation in GPADA will be updated
by results from the GPADres register. While
enabled, the GPADT elapsed time counter will
increment. When “AccV” is cleared to ‘0’,
GPADA accumulation will be disabled.
tsel
Temperature Accumulation selection: Selects
temperature sensing source used for
accumulation.
0 = internal temperature sensor is used
1 = external temperature sensor is used
Reserved
Reserved bit.
ISL6295
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6295 | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85 |
| ISL6295CV | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85 |
| ISL6299AIRZ | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL6299A | Quadruple 2-Input Exclusive-OR Gates 14-SSOP -40 to 85 |
| ISL6299AIRZ-T | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6295CVZ | 功能描述:IC FUEL GAUGE LOW VOLTAGE8-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| ISL6295CVZ-T | 功能描述:IC FUEL GAUGE LOW VOLTAGE8-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL6295EVAL1 | 制造商:Intersil Corporation 功能描述:LOW VOLT FUEL GAUGE - Bulk |
| ISL6296 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:FlexiHash For Battery Authentication |
| ISL6296_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:FlexiHash⑩ For Battery Authentication |
發布緊急采購，3分鐘左右您將得到回復。