- 您現在的位置：買賣IC網 > PDF目錄383144 > ISL6292CCR3Z (INTERSIL CORP) Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6292CCR3Z |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | 3 X 3 MM, LEAD-FREE, PLASTIC, DFN-10 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 436K |
| 代理商： | ISL6292CCR3Z |
8
FN9133.2
July 22, 2005
Recharge
After a charge cycle completes, charging is prohibited until
the battery voltage drops to a recharge threshold, V
RECHRG
(see Electrical Specifications). Then a new charge cycle
starts at point t
6
and ends at point t
8
, as shown in Figure 5.
The safety timer is reset at t
6
.
Internal Oscillator
The internal oscillator establishes a timing reference. The
oscillation period is programmable with an external timing
capacitor, C
TIME
, as shown in Typical Applications. The
oscillator charges the timing capacitor to 1.5V and then
discharges it to 0.5V in one period, both with 10
μ
A current.
The period T
OSC
is:
(EQ. 3)
A 1nF capacitor results in a 0.2ms oscillation period. The
accuracy of the period is mainly dependent on the accuracy
of the capacitance and the internal current source.
Total Charge Time
The total charge time for the CC mode and CV mode is
limited to a length of TIMEOUT. A 22-stage binary counter
increments each oscillation period of the internal oscillator to
set the TIMEOUT. The TIMEOUT can be calculated as:
(EQ. 4)
A 1nF capacitor leads to 14 minutes of TIMEOUT. For
example, a 15nF capacitor sets the TIMEOUT to be 3.5
hours. The charger has to reach the end-of-charge condition
before the TIMEOUT, otherwise, a TIMEOUT fault is issued.
The TIMEOUT fault latches up the charger. There are two
ways to release such a latch-up: either to recycle the input
power, or toggle the EN pin to disable the charger and then
enable it again.
The trickle mode charge has a time limit of 1/8 TIMEOUT. If
the battery voltage does not reach V
MIN
within this limit, a
TIMEOUT fault is issued and the charger latches up. The
charger stays in trickle mode for at least 15 cycles of the
internal oscillator and, at most, 1/8 of TIMEOUT, as shown in
Figure 5.
Charge Current Programming
The charge current in the CC mode is programmed by the
IREF pin. The voltage of IREF is regulated to a 0.8V
reference voltage. The charging current during the constant
current mode is 100,000 times that of the current in the
R
IREF
resistor. Hence, the charge current is,
(EQ. 5)
Table 1 shows the charge current vs. selected R
IREF
values.
The ISL6292C is designed to be safe when the IREF pin is
accidentally short-circuited to an external source or to
ground. If the IREF pin is driven by an external source to
below 0.38V or above 1.5V for any reason, the charger is
disabled and the FAULT pin turns to LOW to indicate a fault
condition. The charger will resume charging after the fault
condition is removed. When the IREF is driven by a voltage
between 0.38V to 0.5V (typical value), the charge current is
limited to 100mA; or when driven to a voltage between 1.2V
to 1.5V, the charge current is limited to 500mA. For any
voltage between 0.5V to 1.2V, the charge current will drop to
a very low value. This feature can protect the charger from a
large charging current when IREF is accidentally shorted to
ground or to a high voltage. Figure 6 shows the charge
current when the IREF pin voltage is driven from 0V to 3V.
End-of-Charge (EOC) Current
The EOC current I
MIN
sets the level at which the charger
starts to indicate the end of the charge with the STATUS pin,
as shown in Figure 5. The charger actually does not
terminate charging until the end of the TIMEOUT, as
described in the Total Charge Time section. In the
T
OSC
0.2 10
6
C
TIME
=
onds
sec
(
)
TIMEOUT
2
22
T
OSC
14
C
-----------------
=
=
minutes
(
)
I
REF
R
IREF
-----------------
10
5
×
A
( )
=
TABLE 1. CHARGE CURRENT vs R
IREF
VALUES (Note)
R
IREF
(k
)
CHARGE CURRENT (mA)
MIN
TYP
MAX
267
250
300
350
160
450
500
550
100
720
800
880
88.9
810
900
990
80
900
1000
1100
NOTE: The limits are still preliminary. Additional samples will be
tested for the final results.
FIGURE 6. CHARGE CURRENT WHEN IREF PIN IS DRIVEN
BY AN EXTERNAL VOLTAGE SOURCE
STATUS
5V/Div
IREF Pin Voltage
500mV/Div
Charge Current
200mA/Div
GND
GND
GND
Time Scale
40s/Div
ISL6292C
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6292DCR4 | Li-ion/Li Polymer Battery Charger |
| ISL6292D | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| ISL6292DCR4-T | Li-ion/Li Polymer Battery Charger |
| ISL6292DCRZ | Li-ion/Li Polymer Battery Charger |
| ISL6295CV-T | Low Voltage Fuel Gauge |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6292CCR3Z-T | 功能描述:IC CHARGER LI-ION POLYMER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL6292D | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL6292DCR4 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL6292DCR4-T | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL6292DCRZ | 功能描述:電池管理 LINEAR SINGLE CELL LI-ION CHRGR 16LD RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。