- 您現在的位置：買賣IC網 > PDF目錄383144 > ISL6292CCR3Z-T (INTERSIL CORP) Li-ion/Li Polymer Battery Charger PDF資料下載
參數資料
| 型號： | ISL6292CCR3Z-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Li-ion/Li Polymer Battery Charger |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | 3 X 3 MM, LEAD-FREE, PLASTIC, DFN-10 |
| 文件頁數： | 6/11頁 |
| 文件大?。?/td> | 436K |
| 代理商： | ISL6292CCR3Z-T |
6
FN9133.2
July 22, 2005
Theory of Operation
The ISL6292C is an integrated charger for single-cell Li-ion
or Li-polymer batteries. The ISL6292C functions as a
traditional linear charger when powered with a voltage-
source adapter. When powered with a current-limited
adapter, the charger minimizes the thermal dissipation
commonly seen in traditional linear chargers.
As a linear charger, the ISL6292C charges a battery in the
popular constant current (CC) and constant voltage (CV)
profile. The constant charge current I
REF
is programmable
up to 1.5A with an external resistor. The charge voltage V
CH
has 1% accuracy over the entire recommended operating
condition range. The charger always preconditions the
battery with 10% of the programmed current at the beginning
of a charge cycle, until the battery voltage is verified to be
above the minimum fast charge voltage, V
MIN
. This low-
current preconditioning charge mode is named trickle mode.
The verification takes 15 cycles of an internal oscillator
whose period is programmable with the timing capacitor. A
thermal-foldback feature removes the thermal concern
typically seen in linear chargers. The charger reduces the
charge current automatically as the IC internal temperature
rises above 100°C to prevent further temperature rise. The
thermal-foldback feature guarantees safe operation when
the printed circuit board (PCB) is space limited for thermal
dissipation.
The charger offers a safety timer for setting the fast charge
time (TIMEOUT) limit to prevent charging a dead battery for
an extensively long time. The trickle mode is limited to 1/8 of
TIMEOUT.
The charger automatically re-charges the battery when the
battery voltage drops below a recharge threshold. When the
wall adapter is not present, the ISL6292C draws less than
1
μ
A current from the battery.
Three indication pins are available from the charger to
indicate the charge status. The V2P8 outputs a 2.8V dc
voltage when the input voltage is above the power-on reset
(POR) level and can be used as the power-present
indication. This pin is capable of sourcing a 2mA current, so
it can also be used to bias external circuits.
The STATUS pin is an open-drain logic output that turns
LOW at the beginning of a charge cycle until the end-of-
charge (EOC) condition is qualified. The EOC condition is:
the battery voltage rises above the recharge threshold and
the charge current falls below a user-programmable EOC
current threshold. Once the EOC condition is qualified, the
STATUS output rises to HIGH and is latched. The latch is
released at the beginning of a charge or re-charge cycle.
The open-drain FAULT pin turns low when a charge time
fault occurs or when the IREF pin is pulled below 0.35V or
above 1.4V.
Figure 3 shows the typical charge curves in a traditional
linear charger powered with a constant-voltage adapter.
From the top to bottom, the curves represent the constant
input voltage, the battery voltage, the charge current and the
power dissipation in the charger. The power dissipation P
CH
is given by the following equation:
(EQ. 1)
where I
CHARGE
is the charge current. The maximum power
dissipation occurs during the beginning of the CC mode. The
maximum power the IC is capable of dissipating is
dependent on the thermal impedance of the printed-circuit
board (PCB). Figure 3 shows, with dotted lines, two cases
that the charge currents are limited by the maximum power
dissipation capability due to the thermal foldback.
FIGURE 3. TYPICAL CHARGE CURVES USING A
CONSTANT-VOLTAGE ADAPTER
V
CH
V
MIN
V
IN
I
REF
I
REF
/10
P
1
P
2
P
3
Trickle
Mode
Constant Current
Mode
Constant Voltage
Mode
Inhibit
TIMEOUT
Input Voltage
Battery Voltage
Charge Current
Power Dissipation
P
CH
V
IN
V
BAT
–
(
)
I
CHARGE
=
FIGURE 4. TYPICAL CHARGE CURVES USING A CURRENT-
LIMITED ADAPTER
V
CH
V
MIN
V
IN
I
REF
I
LIM
I
REF
/10
P
1
P
2
Trickle
Mode
Constant Current
Mode
Constant Voltage
Mode
Inhibit
TIMEOUT
Input Voltage
Battery Voltage
Charge Current
Power Dissipation
ISL6292C
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6292CCR3Z | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| ISL6292DCR4 | Li-ion/Li Polymer Battery Charger |
| ISL6292D | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| ISL6292DCR4-T | Li-ion/Li Polymer Battery Charger |
| ISL6292DCRZ | Li-ion/Li Polymer Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6292D | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL6292DCR4 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL6292DCR4-T | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL6292DCRZ | 功能描述:電池管理 LINEAR SINGLE CELL LI-ION CHRGR 16LD RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| ISL6292DCRZ-T | 功能描述:電池管理 LINEAR SINGLE CELL LI-ION CHRGR 16LD RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。