- 您現在的位置：買賣IC網 > PDF目錄383142 > ISL6219A (Intersil Corporation) Microprocessor CORE Voltage Regulator Precision Multi-Phase BUCK PWM Controller for Mobile Applications PDF資料下載
參數資料
| 型號： | ISL6219A |
| 廠商： | Intersil Corporation |
| 英文描述： | Microprocessor CORE Voltage Regulator Precision Multi-Phase BUCK PWM Controller for Mobile Applications |
| 中文描述： | 微處理器核心電壓調節精度多相降壓PWM控制器，用于移動應用 |
| 文件頁數： | 11/17頁 |
| 文件大?。?/td> | 408K |
| 代理商： | ISL6219A |
11
external enable circuit must release the FS/EN pin to float to the
designed 1.23V level.
The 11111 VID code is reserved as a signal to the controller
that no load is present. The controller will enter shut-down
mode after receiving this code and will start up upon
receiving any other code.
To enable the controller, VCC must be greater than the POR
threshold; FS/EN must be greater than 1V; and VID cannot
be equal to 11111. Once these conditions are true, the
controller immediately initiates a soft start sequence.
SOFT-START
After the POR function is completed with V
CC
reaching
4.38V, the soft-start sequence is initiated. Soft-Start, by its
slow rise of CORE voltage from zero, avoids an over-current
condition by slowly charging the output capacitors. This
voltage rise is initiated by an internal DAC that slowly raises
the reference voltage to the error amplifier input. The voltage
rise is controlled by the oscillator frequency and the DAC
within the controller, therefore, the output voltage is
CORE voltage value.
For the first 32 PWM switching cycles, the DAC output
remains inhibited and the PWM outputs remain in a high-
impedance state. From the 33rd cycle and for another,
approximately 150 cycles the PWM output remains low,
clamping the lower output MOSFETs to ground. The time
variability is due to the error amplifier, sawtooth generator and
comparators moving into their active regions. After this short
interval, the PWM outputs are enabled and increment the
PWM pulse width from zero duty cycle to operational pulse
width, thus allowing the output voltage to slowly reach the
CORE voltage. The CORE voltage will reach its programmed
value before the 2048 cycles, but the PGOOD output will not
be initiated until the 2048th PWM switching cycle.
The soft-start time, t
SS
, is determined by an 11-bit counter
that increments with every pulse of the phase clock. For
example, a converter switching at 300kHz has a soft-start
time of
11
SW
Figure 9 shows the waveforms when the regulator is
operating at 300kHz. Note that the soft-start duration is a
function of the Channel Frequency as explained previously.
DYNAMIC VID
The ISL6219A is capable of executing on-the-fly output-
voltage changes. At the beginning of the phase-1 switching
cycle (defined in the section entitled
PWM Operation
), the
ISL6219A checks for a change in the VID code. The VID
code is the bit pattern present at pins VID4-VID0 as outlined
in
Voltage Regulation
. If the new code remains stable for
another full cycle, the ISL6219A begins incrementing the
reference by making 25mV change every two switching
cycles until it reaches the new VID code.
Since the ISL6219A recognizes VID-code changes only at
the beginning of a switching cycle, up to one full cycle may
pass before a VID change registers. This is followed by a
one-cycle wait before the output voltage begins to change.
Thus, the total time required for a VID change, t
DV
, is
dependent on the switching frequency (f
S
), the size of the
change (
V
ID
), and the time before the next switching cycle
begins. The one-cycle uncertainty in Equation 6 is due to the
possibility that the VID code change may occur up to one full
cycle before being recognized. The time required for a
converter running with f
S
= 500kHz to make a 1.5V to 1.7V
reference-voltage change is between 30
μ
s and 32
μ
s as
calculated using Equation 6. This example is also illustrated
in Figure 10.
.
T
SS
----------
---------------------
6.8ms
=
=
=
(EQ. 5)
FIGURE 9. START-UP OF 3 PHASE SYSTEM OPERATING AT
300kHz
1ms/div
0V
0V
VCORE, 1V/div
0V
PGOOD, 5V/div
FS/EN, 2V/div
SS Interval
0V
V
COMP
, 1V/div
FIGURE 10. DYNAMIC-VID WAVEFORMS FOR 500KHz
ISL6219A BASED MULTI-PHASE BUCK
CONVERTER
5
μ
s/div
V
REF
, 100mV/div
V
OUT
, 100mV/div
1.5V
V
ID
, 5V/div
01110
00110
1.5V
VID CHANGE OCCURS
ANYWHERE HERE
ISL6219A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6219ACA | Microprocessor CORE Voltage Regulator Precision Multi-Phase BUCK PWM Controller for Mobile Applications |
| ISL6219ACA-T | Octal D-Type Edge-Triggered Flip-Flops With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6219 | Octal D-Type Edge-Triggered Flip-Flops With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6219CA | DB50 FEMALE SOLDER SHELL |
| ISL6223CA-T | Mobile Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6219A_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Precision Multi-Phase BUCK PWM Controller for Mobile Applications |
| ISL6219ACA | 功能描述:IC REG CTRLR BUCK PWM VM 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6219ACA-T | 功能描述:IC REG CTRLR BUCK PWM VM 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6219ACAZ | 功能描述:IC REG CTRLR BUCK PWM VM 28-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| ISL6219ACAZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 28-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。