- 您現在的位置：買賣IC網 > PDF目錄16332 > ISL59448EVAL1Z (Intersil)EVAL BOARD 1 FOR ISL59448 PDF資料下載
參數資料
| 型號： | ISL59448EVAL1Z |
| 廠商： | Intersil |
| 文件頁數： | 5/14頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD 1 FOR ISL59448 |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
13
FN6160.2
March 29, 2006
PC Board Layout
The AC performance of this circuit depends greatly on the
care taken in designing the PC board. The following are
recommendations to achieve optimum high frequency
performance from your PC board.
The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended.
Minimize signal trace lengths. Trace inductance and
capacitance can easily limit circuit performance. Avoid
sharp corners, use rounded corners when possible. Vias
in the signal lines add inductance at high frequency and
should be avoided. PCB traces greater than 1" begin to
exhibit transmission line characteristics with signal rise/fall
times of 1ns or less. High frequency performance may be
degraded for traces greater than one inch, unless strip line
are used.
Match channel-channel analog I/O trace lengths and
layout symmetry. This will minimize propagation delay
mismatches.
Maximize use of AC de-coupled PCB layers. All signal I/O
lines should be routed over continuous ground planes (i.e.
no split planes or PCB gaps under these lines). Avoid vias
in the signal I/O lines.
Use proper value and location of termination resistors.
Termination resistors should be as close to the device as
possible.
When testing use good quality connectors and cables,
matching cable types and keeping cable lengths to a
minimum.
Minimum of 2 power supply de-coupling capacitors are
recommended (1000pF, 0.01F) as close to the devices
as possible - Avoid vias between the cap and the device
because vias add unwanted inductance. Larger caps can
be farther away. When vias are required in a layout, they
should be routed as far away from the device as possible.
The NIC pins are placed on both sides of the input pins.
These pins are not internally connected to the die. It is
recommended these pins be tied to ground to minimize
crosstalk.
ISL59448
相關PDF資料 |
PDF描述 |
|---|---|
| EYM08DRMD-S664 | CONN EDGECARD 16POS .156 WW |
| 2-6278876-0 | C/A 50.125UM RIS MTRJ 20M1 |
| VE-B1T-EY-S | CONVERTER MOD DC/DC 6.5V 50W |
| VE-B1N-EY-S | CONVERTER MOD DC/DC 18.5V 50W |
| ECM22DRXN | CONN EDGECARD 44POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59448IAZ | 功能描述:IC AMP TRIPLE MUX 500MHZ 24-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59448IAZ-T7 | 功能描述:IC AMP MUX 2:1 500MHZ 24-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ISL59450 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Multiformat Video Crosspoint with Integrated Sync Separator |
| ISL59450IQZ | 功能描述:IC SWITCH VID CRSSPNT 128-MQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| ISL59450IQZ-EVAL | 制造商:Intersil Corporation 功能描述:ISL59450IQZ-EVAL EVALUATION BOARD - Bulk |
發布緊急采購，3分鐘左右您將得到回復。