- 您現在的位置：買賣IC網 > PDF目錄383134 > ISL54200 (Intersil Corporation) USB 2.0 High/Full Speed Multiplexer PDF資料下載
參數資料
| 型號： | ISL54200 |
| 廠商： | Intersil Corporation |
| 英文描述： | USB 2.0 High/Full Speed Multiplexer |
| 中文描述： | USB2.0高/全速多路復用器 |
| 文件頁數： | 9/16頁 |
| 文件大小： | 1113K |
| 代理商： | ISL54200 |
9
FN6408.0
January 24, 2007
The HSx switches can also pass USB full-speed signals
(12Mbps) with minimal distortion and meet all the USB
requirements for USB 2.0 full-speed signaling. See full-
speed eye diagram Figure 11.
The maximum signal range for the HSx switches is from
-1.5V to V
DD
. The signal voltage should not be allow to
exceed the V
DD
voltage rail or go below ground by more
than -1.5V.
The HSx switches are active (turned ON) whenever the IN
voltage is
≥
1.4V and the EN logic voltage
≥
1.4V when
operated with a 2.7V to 3.6V supply.
ISL54200 Operation
The discussion that follows will discuss using the ISL54200 in
the typical application shown in the block diagram on page 9.
POWER
The power supply connected at the VDD (pin 1) provides the
DC bias voltage required by the ISL54200 part for proper
operation. The ISL54200 can be operated with a VDD
voltage in the range of 2.7V to 5.5V. When used in a USB
application the VDD voltage should be kept in the range of
3.0V to 5.5V to ensure you get the proper signal levels for
good signal quality.
A 0.01μF or 0.1μF decoupling capacitor should be
connected from the VDD pin to ground to filter out any power
supply noise from entering the part. The capacitor should be
located as close to the VDD pin as possible.
LOGIC CONTROL
The state of the ISL54200 device is determined by the
voltage at the IN pin (pin 2) and the EN pin (pin 10). IN is
only active when the EN pin is logic “1” (High). Refer to“Truth
Table” on page 2.
The EN pin is internally pulled low through a 4M
Ω
resistor to
ground. For logic “0” (Low) it can be driven low or allowed to
Float. The IN pin must be driven low or high and cannot be
left floating.
Logic control voltage levels:
EN = Logic “0” (Low) when V
EN
≤
0.5V or Floating.
EN = Logic “1” (High) when V
EN
≥
1.4V
IN = Logic “0” (Low) when V
IN
≤
0.5V.
IN = Logic “1” (High) when V
IN
≥
1.4V
Full-speed Mode
If the IN pin = Logic “0” and EN pin = Logic “1” the part will be
in the full-speed mode. In this mode the FSD1 and FSD2
switches are ON and the HSD1 and HSD2 switches are OFF
(high impedance). In a typical application V
DD
will be in the
range of 2.8V to 3.6V and will be connected to the battery or
LDO of the portable media device. When a computer or USB
hub is plugged into the common USB connector and the part
is in the full-speed mode a link will be established between
the full-speed driver section of the media player and the
computer. The device will be able to transmit and receive
data from the computer at a data rate of 12Mbps.
High-speed Mode
If the IN pin = Logic “1” and EN pin = Logic “1” the part will go
into high-speed mode. In high-speed mode the HSD1 and
HSD2 switches are ON and the FSD1 and FSD2 switches
are OFF (high impedance). When a USB cable from a
computer or USB hub is connected at the common USB
connector and the part is in the high-speed mode a link will
be established between the high-speed driver section of the
media player and the computer. The device will be able to
transmit and receive data from the computer at a data rate of
480Mbps.
All Switches OFF Mode
If the IN pin = Logic “0” or Logic “1” and EN pin = Logic “0” all
of the switches will turn OFF (high impedance).
The all OFF state can be used to switch between the two
USB sections of the media player. When disconnecting from
one USB device to the other USB device you can
momentarily put the ISL54400 switch in the “all off” state in
order to get the computer to disconnect from the one device
so it can properly connect to the other USB device when that
channel is turned ON.
ISL54200
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54200IRZ | USB 2.0 High/Full Speed Multiplexer |
| ISL54200IRZ-T | USB 2.0 High/Full Speed Multiplexer |
| ISL54400EVAL1Z | Low Voltage, Dual SPDT, USB/Audio Switches with Negative Signal Capability |
| ISL54400IRUZ-T | Low Voltage, Dual SPDT, USB/Audio Switches with Negative Signal Capability |
| ISL54400IRZ | Low Voltage, Dual SPDT, USB/Audio Switches with Negative Signal Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54200_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:USB 2.0 High/Full Speed Multiplexer |
| ISL54200EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL54200 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL54200IRUZ-T | 功能描述:IC USB SWITCH DUAL SPDT 10UTQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:2,500 系列:- 功能:視頻交叉點開關 電路:1 x 8:6 導通狀態電阻:- 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3.135 V ~ 5.25 V 電流 - 電源:55mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:24-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1214 (CN2011-ZH PDF) 其它名稱:FMS6502MTC24XTR |
| ISL54200IRZ | 功能描述:IC USB SWITCH DUAL SPDT 10TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54200IRZ-T | 功能描述:IC USB SWITCH DUAL SPDT 10TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。