- 您現在的位置：買賣IC網 > PDF目錄1927 > ISL54105CRZ (Intersil)IC TMDS REGENERATOR 72-QFN PDF資料下載
參數資料
| 型號： | ISL54105CRZ |
| 廠商： | Intersil |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TMDS REGENERATOR 72-QFN |
| 標準包裝： | 1,680 |
| 應用： | 多媒體顯示器，測試設備 |
| 接口： | I²C |
| 電源電壓： | 3 V ~ 3.6 V |
| 封裝/外殼： | 72-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 72-QFN（10x10） |
| 包裝： | 托盤 |
| 安裝類型： | 表面貼裝 |
12
FN6723.0
June 11, 2008
of skew relative to the incoming green and blue. The FIFO’s
quantization (worst case) increases the total skew to 4.0 bits.
While increasing skew is not desirable, DVI and HDMI
receivers are required to have a minimum of 6 bits of
inter-pair skew tolerance, so the addition of 2 bits of skew is
only a problem with the most pathological cables and
transmitters. It does, however, limit the number of ISL54105s
that can be put in series (although statistically, it is unlikely
that all the skews would line up in a worst-case
configuration).
PCB Layout Recommendations
Because of the high speed of the TMDS signals, careful
PCB layout is critical to maximize performance. The
following guidelines should be adhered to as closely as
possible:
All TMDS pair traces should have a characteristic
impedance of 50
Ω with respect to the power/ground
planes and 100
Ω with respect to each other. Failure to
meet this requirement will increase reflections, shrinking
the available eye.
Avoid vias for all 3 high speed TMDS pairs. Vias add
inductance which causes a discontinuity in the
characteristic impedance of the trace. Keep all the traces
on the top (or the bottom) of the PCB. The TMDS clock
can have vias if necessary, since it is lower speed and less
critical. If you must use a via, ensure the vias are
symmetrical (put identical vias in both lines of the
differential pair).
For each TMDS channel, the trace lengths of the 3 TMDS
pairs (0, 1 and 2) should ideally be the same to reduce
inter channel skew introduced by the board.
The trace length of the clock pair is not critical at all.
Since the clock is only used as a frequency reference, its
phase/delay is inconsequential. In addition, since the
TMDS clock frequency is 1/10th the pixel rate, the clock
signal itself is much more noise-immune. So liberties
(such as vias and circuitous paths) can be taken when
routing the clock lines.
Minimize capacitance on all TMDS lines. The lower the
capacitance, the sharper the rise and fall times.
Maintain a constant, solid ground (or power) plane under
the 3 high speed TMDS signals. Do not route the signals
over gaps in the ground plane or over other traces.
Ideally each supply should be bypassed to ground with a
0.1F capacitor. Minimize trace length and vias to
minimize inductance and maximize noise rejection.
Figure 12 demonstrates a common but non-ideal PCB
layout and its equivalent circuit. The additional trace
resistance between the bypass capacitor and the power
supply/IC reduces its effectiveness. Figure 13
demonstrates a better layout. In this case there is still
series trace resistance (it is impossible to completely
eliminate it), but now it is being put to good use, as part of
a “T” filter, attenuating supply noise before it gets to the IC,
and reducing the amount of IC-generated noise that gets
injected into the supply. Follow the good supply bypassing
rules shown in Figure 13 to the extent possible.
FIGURE 11. MAXIMUM ADDITIONAL INTERCHANNEL SKEW
FOR INPUTS WITH MODERATE TO LARGE
SKEW
Bit 4
Bit 5
Bit 0
Bit 1
Bit 2
Bit 3
Bit 7
Bit 8
Bit 9
Bit 4
Bit 5
Bit 6
Bit 7
Bit 0
Bit 1
Bit 2
Bit 3
Bit 7
Bit 8
Bit 9
Bit 4
Bit 5
Bit 6
Bit 7
Bit 0
Bit 1
Bit 2
Bit 3
Bit 7
Bit 8
Bit 9
Bit 4
Bit 0
Bit 1
Bit 2
Bit 3
Bit 6
Bit 7
Bit 8
Bit 9
Bit 4
Bit 5
Bit 6
Bit 7
Bit 0
Bit 1
Bit 2
Bit 3
Bit 7
Bit 8
Bit 9
Bit 4
Bit 5
Bit 6
Bit 7
Bit 0
Bit 1
Bit 2
Bit 3
Bit 8
Bit 9
INPUT SKEW
(2.3 bits/1.4ns
in this example)
OUTPUT SKEW
(4 bits/2.5ns at
162.5Mpixels/s)
Bit 5
Bit 6
Bit 4
Bit 5
Bit 8
FIGURE 12. SUB-OPTIMAL BYPASS CAPACITOR LAYOUT
CBYPASS
RTRACE
V
+
RTRACE
IC
V
+
GND
GROUND PLANE
POWER PLANE
CBYPASS
IC
V
+
GND
VIAS
TO
GND
VIA TO
POWER
PLANE
EQUIVALENT CIRCUIT
RVIA
ISL54105
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54200IRZ-T | IC USB SWITCH DUAL SPDT 10TDFN |
| ISL54205AIRZ-T | IC SWITCH MP3/USB2.0 HS 10-TDFN |
| ISL54205BIRTZ-T | IC USB SWITCH DUAL SPDT 10TDFN |
| ISL54206AIRTZ-T | IC USB SWITCH DUAL SPDT 10TDFN |
| ISL54206IRZ-T | IC SWITCH MP3/USB2.0 HS 10-TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54105CRZ-EVALZ | 制造商:Intersil Corporation 功能描述:ISL54105CRZ EVALUATION BOARD, ROHS - Bulk |
| ISL54106ACRZ | 功能描述:IC TMDS REGENERATOR MUX RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ISL54106CRZ | 功能描述:IC TMDS REGENERATOR MUX RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ISL54111CATX-EVALZ | 制造商:Intersil Corporation 功能描述:ISL54111CATX EVALUATION BOARD - ROHS COMPLIANT - Bulk |
| ISL54111HDMI-EVALZ | 制造商:Intersil Corporation 功能描述:ISL54111HDMI EVALUATION BOARD - ROHS COMPLIANT - Bulk |
發布緊急采購，3分鐘左右您將得到回復。