- 您現在的位置：買賣IC網 > PDF目錄383130 > ISL4245EIR (INTERSIL CORP) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | ISL4245EIR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 通用總線功能 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | TRIPLE LINE TRANSCEIVER, PQCC32 |
| 封裝： | 5 X 5 MM, PLASTIC, MO-220VHHD-2, QFN-32 |
| 文件頁數： | 10/17頁 |
| 文件大?。?/td> | 457K |
| 代理商： | ISL4245EIR |
10
Powerdown Functionality
The already low current requirement drops significantly
when the device enters powerdown mode. In powerdown,
supply current drops to 10nA, because the on-chip charge
pump turns off (V+ collapses to V
CC
, V- collapses to GND),
and the transmitter outputs tristate. Inverting receiver
outputs disable only in manual powerdown; refer to Table 2
for details. This micro-power mode makes these devices
ideal for battery powered and portable applications.
Software Controlled (Manual) Powerdown
These devices allow the user to force the IC into the low
power, standby state, and utilize a two pin approach where
the FORCEON and FORCEOFF inputs determine the IC’s
mode. For always enabled operation, FORCEON and
FORCEOFF are both strapped high. To switch between
active and powerdown modes, under logic or software
control, only the FORCEOFF input need be driven. The
FORCEON state isn’t critical, as FORCEOFF dominates
over FORCEON. Nevertheless, if strictly manual control over
powerdown is desired, the user must strap FORCEON high
to disable the enhanced automatic powerdown circuitry.
ISL4238E/4XE inverting (standard) receiver outputs also
disable when the device is in manual powerdown, thereby
eliminating the possible current path through a shutdown
peripheral’s input protection diode (see Figures 2 and 3).
Connecting FORCEOFF and FORCEON together disables
the enhanced automatic powerdown feature, enabling them
to function as a manual SHUTDOWN input (see Figure 4).
With any of the above control schemes, the time required to
exit powerdown, and resume transmission is only 100
μ
s.
When using both manual and enhanced automatic
powerdown (FORCEON = 0), the ISL4238E/4XE won’t
power up from manual powerdown until both FORCEOFF
and FORCEON are driven high, or until a transition occurs
on a receiver or transmitter input. Figure 5 illustrates a circuit
for ensuring that the ISL4238E/4XE powers up as soon as
FORCEOFF switches high. The rising edge of the Master
Powerdown signal forces the device to power up, and the
ISL4238E/4XE returns to enhanced automatic powerdown
mode an RC time constant after this rising edge. The time
constant isn’t critical, because the ISL4238E/4XE remains
powered up for 30 seconds after the FORCEON falling edge,
even if there are no signal transitions. This gives slow-to-
wake systems (e.g., a mouse) plenty of time to start
transmitting, and as long as it starts transmitting within 30
seconds both systems remain enabled.
INVALID Output
The INVALID output always indicates (see Table 2) whether
or not 30
μ
s have elapsed with invalid RS-232 signals (see
Figures 6 and 9) persisting on all of the receiver inputs,
giving the user an easy way to determine when the interface
block should power down. Invalid receiver levels occur
whenever the driving peripheral’s outputs are shut off
(powered down) or when the RS-232 interface cable is
disconnected. In the case of a disconnected interface cable
where all the receiver inputs are floating (but pulled to GND
FIGURE 3. DISABLED RECEIVERS PREVENT POWER DRAIN
ISL4238E/4XE
TRANSITION
DETECTOR
R
X
T
X
R
OUTB
R
OUT
T1
IN
FORCEOFF = GND
V
CC
V
CC
TO
R
IN
T1
OUT
V
OUT
=
HI-Z
POWERED
DOWN
UART
WAKE-UP
LOGIC
FIGURE 4. CONNECTIONS FOR MANUAL POWERDOWN
WHEN NO VALID RECEIVER SIGNALS ARE
PRESENT
PWR
MGT
LOGIC
FORCEOFF
INVALID
CPU
I/O
FORCEON
ISL4238E/4XE
UART
FIGURE 5. CIRCUIT TO ENSURE IMMEDIATE POWER UP
WHEN EXITING FORCED POWERDOWN
FORCEOFF
FORCEON
POWER
MANAGEMENT
UNIT
MASTER POWERDOWN LINE
1M
0.1
μ
F
ISL4238E/4XE
ISL4238E, ISL4244E, ISL4245E
相關PDF資料 |
PDF描述 |
|---|---|
| ISL4245EIRZ | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ISL4238E | QFN Packaged, ±15kV ESD Protected, +2.7V to +5.5V, 10Nanoamp, 250kbps/1Mbps, RS-232 Transceivers with Enhanced Automatic Powerdown(QFN封裝, ±15kV ESD 防護, +2.7V至+5.5V, 10Nanoamp, 250kbps/1Mbps, 具有自動斷電功能的RS-232收發器) |
| ISL4244E | QFN Packaged, ±15kV ESD Protected, +2.7V to +5.5V, 10Nanoamp, 250kbps/1Mbps, RS-232 Transceivers with Enhanced Automatic Powerdown(QFN封裝, ±15kV ESD 防護, +2.7V至+5.5V, 10Nanoamp, 250kbps/1Mbps, 具有自動斷電功能的RS-232收發器) |
| ISL4238EIRZ | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ISL4238EIRZ-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL4245EIR-T | 功能描述:IC 3DRVR/5RCVR RS232 3V 32-QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| ISL4245EIRZ | 功能描述:RS-232接口集成電路 RS232 3V 3D/5R 15KV 1MBPS E-DWN 32QFN IN RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ISL4245EIRZ-T | 功能描述:IC XMITTER/RCVR ESD RS232 32-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:發射器 驅動器/接收器數:4/0 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISL4260E | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:QFN Packaged, ±15kV ESD Protected, +3V to +5.5V, 150nA, 250kbps, RS-232 Transmitters/Receivers with Separate Logic Supply |
| ISL4260EIR | 功能描述:IC 3DRVR/2RCVR RS232 3V 32-QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。