- 您現在的位置：買賣IC網 > PDF目錄383130 > ISL4221E (Intersil Corporation) QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kbps, RS-232 Transmitters/Receivers(QFN 封裝, +/-15kV ESD 防護, +2.7V至+5.5V, 150毫微安, 250kbps, RS-232收發器) PDF資料下載
參數資料
| 型號： | ISL4221E |
| 廠商： | Intersil Corporation |
| 英文描述： | QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kbps, RS-232 Transmitters/Receivers(QFN 封裝, +/-15kV ESD 防護, +2.7V至+5.5V, 150毫微安, 250kbps, RS-232收發器) |
| 中文描述： | QFN封裝，/ - 15kV的ESD保護，2.7V至5.5V，150Nanoamp，250kbps的和RS - 232發送器/接收器封裝（QFN封裝，/ - 15kV的ESD防護，為2.7V至5.5V的，150毫微安，250kbps的，的RS - 232收發器） |
| 文件頁數： | 6/13頁 |
| 文件大?。?/td> | 401K |
| 代理商： | ISL4221E |
6
and V- supplies are pumped up to the nominal values),
resulting in significant power savings.
Transmitters
The transmitters are proprietary, low dropout, inverting
drivers that translate TTL/CMOS inputs to EIA/TIA-232
output levels. Coupled with the on-chip
±
5.5V supplies, these
transmitters deliver true RS-232 levels over a wide range of
single supply system voltages.
All transmitter outputs disable and assume a high
impedance state when the device enters the powerdown
mode (see Table 2). These outputs may be driven to
±
12V
when disabled.
The devices guarantee a 250kBps data rate for full load
conditions (3k
and 1000pF), V
CC
≥
3.0V, with one
transmitter operating at full speed. Under more typical
conditions of V
CC
≥
3.3V, R
L
= 3k
, and C
L
= 250pF, one
transmitter easily operates at 900kBps.
Transmitter inputs float if left unconnected, and may cause
I
CC
increases. Connect unused inputs to GND for the best
performance.
Receivers
All the ISL422XE devices contain standard inverting
receivers that three-state via the EN control line. All the
receivers convert RS-232 signals to CMOS output levels and
accept inputs up to
±
25V while presenting the required 3k
to 7k
input impedance (see Figure 1) even if the power is
off (V
CC
= 0V). The receivers’ Schmitt trigger input stage
uses hysteresis to increase noise immunity and decrease
errors due to slow input signal transitions.
Receivers driving a powered down UART must be disabled
to prevent current flow through, and possible damage to, the
UART’s protection diodes (see Figures 2 and 3). This can be
accomplished on the ISL422XE by driving the EN input high
whenever the UART powers down. Figure 3 also shows that
the INVALID output can be used to determine when the
UART should be powered down. When the RS-232 cable is
disconnected, INVALID switches low indicating that the
UART is no longer needed. Reconnecting the cable drives
INVALID back high, indicating that the UART should be
powered up.
Low Power Operation
These 3V devices require a nominal supply current of
0.3mA, even at V
CC
= 5.5V, during normal operation (not in
powerdown mode). This is considerably less than the 5mA to
11mA current required by comparable 5V RS-232 devices,
allowing users to reduce system power simply by switching
to this new family.
Powerdown Functionality
The already low current requirement drops significantly
when the device enters powerdown mode. In powerdown,
supply current drops to 150nA, because the on-chip charge
pump turns off (V+ collapses to V
CC
, V- collapses to GND),
and the transmitter outputs three-state. Receiver outputs are
unaffected by powerdown; refer to Table 2 for details. This
micro-power mode makes the ISL422XE ideal for battery
powered and portable applications.
Software Controlled (Manual) Powerdown
The ISL422XE family provides pins that allow the user to
force the IC into the low power, standby state.
The ISL422XE utilize a two pin approach where the
FORCEON and FORCEOFF inputs determine the IC’s
R
XOUT
GND
≤
V
ROUT
≤
V
CC
5k
R
XIN
-25V
≤
V
RIN
≤
+25V
GND
V
CC
FIGURE 1. INVERTING RECEIVER CONNECTIONS
FIGURE 2. POWER DRAIN THROUGH POWERED DOWN
PERIPHERAL
OLD
V
CC
POWERED
DOWN
UART
GND
SHDN = GND
V
CC
Rx
Tx
V
CC
CURRENT
FLOW
V
OUT
=
V
CC
RS-232 CHIP
FIGURE 3. DISABLED RECEIVERS PREVENT POWER DRAIN
ISL422XE
TRANSITION
DETECTOR
R
X
T
X
INVALID
R
OUT
T
IN
V
CC
V
CC
TO
R
IN
T
OUT
V
OUT
=
HI-Z
POWERED
DOWN
UART
WAKE-UP
LOGIC
EN = V
CC
ISL4221E, ISL4223E
相關PDF資料 |
PDF描述 |
|---|---|
| ISL4223E | QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kbps, RS-232 Transmitters/Receivers(QFN 封裝, +/-15kV ESD 防護, +2.7V至+5.5V, 150毫微安, 250kbps, RS-232收發器) |
| ISL4221 | QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kBps, RS-232 Transmitters/Receivers |
| ISL4221EIR | QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kBps, RS-232 Transmitters/Receivers |
| ISL4221EIRZ-T | QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kBps, RS-232 Transmitters/Receivers |
| ISL4223EIR | RES, SM 1.3K OHM 1/10W 1% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL4221E_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:QFN Packaged, 【15kV ESD Protected, +2.7V to +5.5V, 150nA, 250kBps, RS-232 Transmitters/Receivers |
| ISL4221EIR | 功能描述:IC TXRX RS232 2.7-5.5V ESD 16QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISL4221EIR-T | 功能描述:IC TXRX 1TX/1RX 3V RS-232 16-QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| ISL4221EIRZ | 功能描述:RS-232接口集成電路 3V RS-232 1TX/1RX -4 0+85 TRANS 16LD 5X5 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ISL4221EIRZ-T | 功能描述:IC XMITTER/RCVR ESD RS232 16-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:發射器 驅動器/接收器數:4/0 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。