- 您現在的位置：買賣IC網 > PDF目錄383130 > ISL3874IK (INTERSIL CORP) Wireless LAN Integrated Medium Access Controller with Baseband Processor with Mini-PCI PDF資料下載
參數資料
| 型號： | ISL3874IK |
| 廠商： | INTERSIL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Wireless LAN Integrated Medium Access Controller with Baseband Processor with Mini-PCI |
| 中文描述： | 1 CHANNEL(S), 11M bps, LOCAL AREA NETWORK CONTROLLER, PBGA192 |
| 封裝： | 14 X 14 MM, PLASTIC, BGA-192 |
| 文件頁數： | 13/33頁 |
| 文件大?。?/td> | 390K |
| 代理商： | ISL3874IK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
13
External Memory Interface
The ISL3874 provides separate external chip selects for
code space and data storage space. Code space is
accessible as data space through an overlay mechanism,
except for an internal ROM. Refer to Figures 6 , 7 and 8 for
ISL3874 memory configuration detail examples.
The maximum possible memory space size is 4Mbytes.
Most of the data store space is reserved for storage of
received and transmitted data, with some areas reserved for
use by firmware. However, a portion of the data store may
be allocated as code store. This permits higher speed
instruction execution, by using fast RAMs, than is possible
from Flash memories. The maximum size of this overlay is
the full code space address range, 128kbytes, and is
allocated in independent sections of 16KBytes each, on
16kbyte boundaries, ranging from the highest address of the
actual physical memory space and extending down.
Mapping code execution to RAM requires the RAM to have
code written into it. Typically, this is done by placing code in a
non-volatile memory such as a Flash in the code space. At
initialization, the code in the non-volatile memory transfers itself
to RAM, maps the appropriate blocks of the code space to the
RAM, and then branches to begin execution from RAM. This
allows low cost, slow Flash devices to hold an entire code
image, which can be executed much faster from RAM. If code
is not placed in an external non-volatile memory as described
here, it must be transferred to the RAM via the Host Interface.
Slow memories are not dynamically sensed. Following reset,
the instruction clock operates with a slower cycle while the
Flash is copied to RAM. Once code has been copied from
Flash to RAM, execution transfers to RAM and the clock is
raised to the normal operating frequency.
As mentioned above, it is feasible to operate without a code
image in a non-volatile memory. In such a system, the
firmware must be downloaded to RAM through the host
interface before operation can commence.
The external SRAM memory must be organized in a 16-bit
width to provide adequate performance to implement the
802.11 protocol at 11Mb/s rates. Systems designed for lower
performance applications may be able to use 8-bit wide
memory.
The minimum external memory is 128kbytes of SRAM,
organized 8 or 16 bits wide. Typical applications, including
802.11 station designs, use 256kbytes organized 128K x 16.
An access point application could make use of the full address
space of the device with 4Mbytes organized a 2M x 16.
The ISL3874 supports 8 or 16-bit code space, and 8 or 16-bit
data space. Code space is typically populated with the least
expensive Flash memory available, usually an 8-bit device.
Data space is usually populated with high-speed RAMs
configured as a 16-bit space. This mixing of 8/16 bit spaces is
fully supported, and may be done in any combination desired
for code and data space.
The ISL3874 supports direct control of single chip 16-bit
wide SRAMs with high/low byte enables, as well as direct
control of a 16-bit space constructed from 8-bit wide SRAMs.
The type of memory configuration is specified via the
appropriate MD pin, sensed when the ISL3874 is reset.
ISL3874 pin MA0/MWEH functions as Address 0 for 8-bit
access, (such as Flash) as MWEH (High Byte Write Enable)
when two x8 memories are configured as a single x16
space, and as the upper Byte Enable when a single x16
memory is used. No external logic is required to generate
the required signals for both types of memory configurations,
even when both exist together; all that is required is for the
ISL3874 code to configure the ISL3874 memory controller to
generate the proper signals for the particular address space
being accessed.
For 8-bit spaces, the ISL3874 dynamically configures pin
MA0/MWEH cycle-by-cycle as the address LSB.
PULLUP
AT45DB011
PULLUP
CS# (TCLKIN)
SCLK (PJ0)
SD (PJ1)
MISO (PJ2)
ISL3874
LARGE SERIAL EEPROM
SMALL SERIAL DEVICES
ISL3874
PULLUP
CS# (TCLKIN)
SCLK (PJ0)
24C08
A2
A1
AO
SDA
SCL
WP
FIGURE 8. SERIAL EEPROM MEMORY INTERFACE
SI
SCK
SO
RESET#
WP#
CS
AT 400kHz AT 3.3V
DC
)
(NOTE: MUST OPERATE
ISL3874
相關PDF資料 |
PDF描述 |
|---|---|
| ISL39300A-DAPDK-CD | PRISM 54Mbps Wireless Local Area Network Access Point |
| ISL39300A-DAPDK | PRISM 54Mbps Wireless Local Area Network Access Point |
| ISL39300A-DAPDK-EVAL | PRISM 54Mbps Wireless Local Area Network Access Point |
| ISL4221EIR-T | QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kBps, RS-232 Transmitters/Receivers |
| ISL4223EIR-T | QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kBps, RS-232 Transmitters/Receivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL3874IK96 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Wireless LAN Integrated Medium Access Controller with Baseband Processor with Mini-PCI |
| ISL3880 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Wireless LAN Integrated Medium Access Controller with Baseband Processor |
| ISL3880IK | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Wireless LAN Integrated Medium Access Controller with Baseband Processor |
| ISL3880IK-TK | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Wireless LAN Integrated Medium Access Controller with Baseband Processor |
| ISL3886 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Wireless LAN Integrated Medium Access Controller with Baseband Processor |
發布緊急采購，3分鐘左右您將得到回復。