- 您現在的位置：買賣IC網 > PDF目錄9870 > ISL3330IAZ-T7A (Intersil)IC TXRX RS232/485 DUAL 20SSOP PDF資料下載
參數資料
| 型號： | ISL3330IAZ-T7A |
| 廠商： | Intersil |
| 文件頁數： | 7/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS232/485 DUAL 20SSOP |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 250 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 2/2 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 3.15 V ~ 3.45 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 帶卷 (TR) |
15
FN6361.0
May 20, 2008
Each RS-485/422 port includes a single receiver (RA), and
the unused Rx output (RB) is disabled.
Worst case receiver input currents are 20% lower than the
1 “unit load” (1mA) RS-485 limit, which translates to a 15k
Ω
minimum input resistance.
These receivers include a “full fail-safe” function that
guarantees a high level receiver output if the receiver inputs
are unconnected (floating), shorted together, or if the bus is
terminated but undriven (i.e., differential voltage collapses to
near zero due to termination). Failsafe with shorted or
terminated and undriven inputs is accomplished by setting
the Rx upper switching point at -40mV, thereby ensuring that
the Rx recognizes a 0V differential as a high level.
All the Rx outputs are short circuit protected, and are
tri-statable via the active high RXEN pin, or when the IC is
Shutdown (SHDN) Mode” on page 16). ISL3331 (QFN)
receiver outputs are also tri-statable via an active low RXEN
input (see “ISL3331 (QFN Package) Special Features” on
For the ISL3331 (QFN), when using the active high RXEN
function, the RXEN pin may be left floating (internally pulled
high), or should be connected to VCC through a 1kΩ resistor.
If using the active low RXEN, then the RXEN pin must be
connected to GND.
TX FEATURES
The RS-485/RS-422 driver is a differential output device that
delivers at least 1.5V across a 54
Ω load (RS-485), and at
least 2V across a 100
Ω load (RS-422). The drivers feature
low propagation delay skew to maximize bit widths, and to
minimize EMI.
To allow multiple drivers on a bus, the RS-485 specification
requires that drivers survive worst case bus contentions
undamaged. The ISL333x drivers meet this requirement via
driver output short circuit current limits, and on-chip thermal
shutdown circuitry. The output stages incorporate current
limiting circuitry that ensures that the output current never
exceeds the RS-485 specification, even at the common
mode voltage range extremes of 12V and -7V. In the event of
a major short circuit condition, devices also include a thermal
shutdown feature that disables the drivers whenever the die
temperature becomes excessive. This eliminates the power
dissipation, allowing the die to cool. The drivers automatically
re-enable after the die temperature drops about +15°C. If the
contention persists, the thermal shutdown/re-enable cycle
repeats until the fault is cleared. Receivers stay operational
during thermal shutdown.
The RS-485 multi-driver operation also requires drivers to
include tri-state functionality, where the port has a DEN pin
to control this function. If the driver is used in an RS-422
network, such that driver tri-state isn’t required, then the
DEN pin should connect to VCC through a 1kΩ resistor.
Drivers are also tri-stated when the IC is in SHDN, or when
the 3.3V power supply is off.
SPEED OPTIONS
The ISL3330 (SSOP) features two speed options that are
user selectable via the SLEW pin: a high slew rate setting
optimized for 20Mbps data rates (Fast), and a slew rate
limited option for operation up to 460kbps (Med). The
ISL3331 (QFN) offers an additional, more slew rate limited,
option for data rates up to 115kbps (Slow). See the “Data
Rate“ and “RS-485 Slew Rate Limited Data Rates” on
page 17 for more information.
Receiver performance is the same for all three speed
options.
DATA RATE, CABLES, AND TERMINATIONS
RS-485/RS-422 are intended for network lengths up to 4000’
(1220m), but the maximum system data rate decreases as
the transmission length increases. Devices operating at the
maximum data rate of 20Mbps are limited to lengths of 20’ to
30’ (6m to 9m), while devices operating at or below 115kbps
can operate at the maximum length of 4000’ (1220m).
Higher data rates require faster edges, so both the ISL333x
versions offer an edge rate capable of 20Mbps data rates.
They both have a second option for 460kbps, but the
ISL3331 also offers another, very slew rate limited, edge rate
to minimize problems at slow data rates. Nevertheless, for
the best jitter performance when driving long cables, the
faster speed settings may be preferable, even at low data
rates. See the “RS-485 Slew Rate Limited Data Rates” on
page 17 for details.
Twisted pair is the cable of choice for RS-485/RS-422
networks. Twisted pair cables tend to pick-up noise and
other electromagnetically induced voltages as common
mode signals, which are effectively rejected by the
differential receivers in these ICs.
The preferred cable connection technique is
“daisy-chaining”, where the cable runs from the connector of
one device directly to the connector of the next device, such
that cable stub lengths are negligible. A “backbone”
structure, where stubs run from the main backbone cable to
each device’s connector, is the next best choice, but care
must be taken to ensure that each stub is electrically “short”.
See Table 4 for recommended maximum stub lengths for
each speed option.
TABLE 4. RECOMMENDED STUB LENGTHS
SPEED OPTION
MAXIMUM STUB LENGTH
ft. (m)
SLOW
350 to 500 (107 to 152)
MED
100 to 150 (30.5 to 46)
FAST
1 to 3 (0.3 to 0.9)
ISL3330, ISL3331
相關PDF資料 |
PDF描述 |
|---|---|
| HIN240CNZ-T | IC 5DRVR/5RCVR RS232 5V 44-MQFP |
| MAX11049ECB+T | IC ADC 16BIT PAR 250KSPS 64TQFP |
| VE-2T2-MX-F4 | CONVERTER MOD DC/DC 15V 75W |
| VE-2T2-MX-F2 | CONVERTER MOD DC/DC 15V 75W |
| MAX11049ETN+T | IC ADC 16BIT 250KSPS SAR 56TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL3331 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Worlda??s Most Power-Effi cient |
| ISL3331EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL3331 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL3331IRZ | 功能描述:IC TXRX 3.3V RS232/485 40-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:發射器 驅動器/接收器數:4/0 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISL3331IRZ-T | 功能描述:IC TXRX 3.3V RS232/485 40-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:發射器 驅動器/接收器數:4/0 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISL3332 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:3.3V, ±15kV ESD Protected, Two Port, Dua Protocol RS-232/RS-485 Transceivers |
發布緊急采購，3分鐘左右您將得到回復。