- 您現在的位置：買賣IC網 > PDF目錄16905 > ISL28476EVAL1Z (Intersil)EVALUATION BOARD FOR ISL28476 PDF資料下載
參數資料
| 型號： | ISL28476EVAL1Z |
| 廠商： | Intersil |
| 文件頁數： | 8/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVALUATION BOARD FOR ISL28476 |
| 標準包裝： | 1 |
| 每 IC 通道數： | 4 - 四 |
| 放大器類型： | 通用 |
| 輸出類型： | 單端，滿擺幅 |
| 轉換速率： | 0.17 V/µs |
| 電流 - 輸出 / 通道： | 31mA |
| 工作溫度： | -40°C ~ 125°C |
| 電流供應（主 IC）： | 240µA |
| 電壓 - 電源，單路/雙路(±)： | 2.4 V ~ 5 V，±1.2 V ~ 2.5 V |
| 板類型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL28476 |
16
FN6301.4
June 23, 2009
Applications Information
Introduction
The ISL28176, ISL28276 and ISL28476 are single, dual and
quad BiCMOS rail-to-rail input, output (RRIO) micropower
precision operational amplifiers. These devices are designed
to operate from a single supply (2.4V to 5.0V) or dual
supplies (±1.2V to ±2.5V) while drawing only 120A
(ISL28276) of supply current. This combination of low power
and precision performance makes these devices suitable for
solar and battery power applications.
Rail-to-Rail Input
Many rail-to-rail input stages use two differential input pairs, a
long-tail PNP (or PFET) and an NPN (or NFET). Severe
penalties have to be paid for this circuit topology. As the input
signal moves from one supply rail to another, the operational
amplifier switches from one input pair to the other causing
drastic changes in input offset voltage and an undesired
change in magnitude and polarity of input offset current.
The devices achieve rail-to-rail input without sacrificing
important precision specifications and degrading distortion
performance. The devices’ input offset voltage exhibits a
smooth behavior throughout the entire common-mode input
range. The input bias current versus the common-mode
voltage range gives us an undistorted behavior from typically
down to the negative rail to 10% higher than the V+ rail (0.5V
higher than V+ when V+ equals 5V).
Input Protection
All input terminals have internal ESD protection diodes to the
positive and negative supply rails, limiting the input voltage
to within one diode beyond the supply rails. Both parts have
additional back-to-back diodes across the input terminals. If
overdriving the inputs is necessary, the external input current
must never exceed 5mA. External series resistors may be
used as an external protection to limit excessive external
voltage and current from damaging the inputs.
Input Bias Current Compensation
The devices contain an input bias cancellation circuit which
reduces the bias currents down to a typical of 500pA while
maintaining an excellent bandwidth for a micro-power
operational amplifier. The input stage transistors are still
biased with adequate current for speed but the canceling
circuit sinks most of the base current, leaving a small fraction
as input bias current.
Rail-to-Rail Output
A pair of complementary MOSFET devices are used to
achieve the rail-to-rail output swing. The NMOS sinks
current to swing the output in the negative direction. The
PMOS sources current to swing the output in the positive
direction. Both parts, with a 100k
Ω load, will typically swing to
within 4mV of the positive supply rail and within 3mV of the
negative supply rail.
4
7
13
V-
Circuit 4
Negative power supply
14
IN+_D
Circuit 1
Amplifier D non-inverting input
15
IN-_D
Circuit 1
Amplifier D inverting input
16
OUT_D
Circuit 3
Amplifier D output
6EN_A
Circuit 2
Amplifier A enable pin internal pull-down; Logic “1”
selects the disabled state; Logic “0” selects the enabled
state.
11
EN_B
Circuit 2
Amplifier B enable pin with internal pull-down; Logic “1”
selects the disabled state; Logic “0” selects the enabled
state.
Pin Descriptions (Continued)
ISL28176
(8 LD SOIC)
ISL28276
(8 LD SOIC)
ISL28276
(16 LD QSOP)
ISL28476
(16 LD QSOP)
PIN
NAME
EQUIVALENT
CIRCUIT
DESCRIPTION
IN-
V+
V-
LOGIC
PIN
V+
V-
V+
V-
OUT
CIRCUIT 3
CIRCUIT 1
CIRCUIT 2
IN+
V+
V-
CAPACITIVELY
COUPLED
ESD CLAMP
CIRCUIT 4
ISL28176, ISL28276, ISL28476
相關PDF資料 |
PDF描述 |
|---|---|
| 0982660153 | CBL 14POS 0.5MM JMPR TYPE A 8" |
| GBC36DCMI | CONN EDGECARD 72POS .100" WW |
| ISL28273INEVAL1Z | EVALUATION BOARD FOR ISL28273 |
| 0982660152 | CBL 14POS 0.5MM JMPR TYPE D 7" |
| ISL28272INEVAL1Z | EVALUATION BOARD FOR ISL28272 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL28476FAZ | 功能描述:IC OPAMP QUAD RRIO MCPWR 16-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
| ISL28476FAZ-T7 | 功能描述:IC OPAMP QUAD RRIO MCPWR 16-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
| ISL28478 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Precision Op-Amp |
| ISL28478EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL28478 RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| ISL28478FAZ | 功能描述:IC OPAMP QUAD RRIO MCPWR 16-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
發布緊急采購，3分鐘左右您將得到回復。